- 您現在的位置：買賣IC網 > PDF目錄1916 > DS33Z44+ (Maxim Integrated Products)IC MAPPER ETHERNET 256CSBGA PDF資料下載
參數資料
| 型號： | DS33Z44+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/59頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MAPPER ETHERNET 256CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 應用： | 數據傳輸 |
| 接口： | 串行 |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 封裝/外殼： | 256-LBGA，CSBGA |
| 供應商設備封裝： | 256-CSBGA（17x17） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
DS33Z44DK
11 of 59
BASIC OPERATION
Powering Up the Design Kit
Attach resource card to main board.
Connect PCB 3.3V and GND banana plugs to power supply. At power-up the system should draw
approximately 1A.
Set switches for software mode as described in Table 2 (short description follows).
Top left bank: All low, except for MODEC0, which is high.
Top right bank: A2, A1, A0 in mid position, SCANTRI low
Bottom Bank: All high (AFCS, FULLDS, H1OS)
General
Upon power-up, the processor FPGA Status LEDs (DS19 green) will be lit. Interrupt LEDs (DS42 red) will not
be lit. DS33Z44 Queue overflow LEDs (DS45, DS46, DS47, DS48 red) will not be lit. PHY LINK LED (DS02,
DS03, DS14 green) should be lit if the Ethernet is connected.
Following are several basic system initializations.
Basic DS33Z44 Initialization (Used for All Quick Setups)
This section covers four basic methods for configuring the Z44. Any one of these initializations can be used with
the following Quick Setup examples:
1.
Upon power-up, the on-board device driver provides a basic configuration for the DS33Z44 and attached
serial cards. This enables traffic to pass from the Ethernet port to the serial port. Consult the device driver
documentation for further details. Device driver behavior is dependant upon jumper settings, which are
detailed in Table 2.
2.
Register-Based Configuration. Launch ChipView.exe and select Register View. When prompted for a
definition file, pick the file named DS33Z44.def. After the definition file loads, go to the File menu and
select File→Memory Config File→Load .MFG file. When prompted, select the file named
4Portsbasic_config.mfg
.
3.
Hardware Mode. Set switches as described in the section for powering up the design kit, then change the
following: HWMODE←3.3V, A0←3.3VV, A1←3.3V, A2←0V. This sets the part for LSB first, scrambling off,
HDLC encapsulated. At this point traffic will pass from the Ethernet port to the serial port. In this mode
broadcast frames are not passed (i.e., ping).
4.
EEPROM mode is available with the DK, but is beyond the scope of this manual.
Quick Setup #1 (Device Driver + CPLD Loopback)
On the serial resource card install jumper 24. Jumpers JP16–JP19 should be set high. This places the card in
CPLD loopback and enables all four ports as described in Table 3.
Complete the hardware configuration and one of the basic DS33Z44 configurations as described in the
previous section.
Using a patch cable, connect the Ethernet connector to an ordinary PC, or network test equipment. This should
cause the link LED to turn on.
At this point any packets sent to the DS33Z44 are echoed back. Incoming packets (i.e., ping) should cause the
RX LED to blink, after which the TX LED should also blink.
To interact with the device driver select from the drop down menu:
Tools→Plugins→Load Plugins. When asked if DLLs have already registered select yes
Select Tools→Plugins→DS33Z44/11/41 Device Driver Demo
A new form called ‘Zchip Configuration’ pops up.
Preload basic configuration for the GUI by selecting File→Load Settings (in the ‘Zchip Configuration’ form).
Select the file named ‘basic_Config.eset’
相關PDF資料 |
PDF描述 |
|---|---|
| DS33ZH11+ | IC MAPPER ETHERNET 100CSBGA |
| DS34C87TN/NOPB | IC LINE DRIVER QUAD CMOS 16-DIP |
| DS34LV87TMX/NOPB | IC LINE DVR QUAD CMOS DIF 16SOIC |
| DS34S132GN+ | IC TDM OVER PACKET 676-BGA |
| DS34T102GN+ | IC TDM OVER PACKET 484TEBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS33Z44+ | 功能描述:網絡控制器與處理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z44DK | 功能描述:以太網開發工具 DS33Z44 Dev Kit RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| DS33ZH11 | 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33ZH11+ | 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS34 | 制造商:LUMILEDS 制造商全稱:LUMILEDS 功能描述:power light source Luxeon V Emitter |
發布緊急采購，3分鐘左右您將得到回復。