- 您現在的位置：買賣IC網 > PDF目錄1994 > DS3105LN+ (Maxim Integrated Products)IC TIMING LINE CARD 64-LQFP PDF資料下載
參數資料
| 型號： | DS3105LN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 66/124頁 |
| 文件大小： | 0K |
| 描述： | IC TIMING LINE CARD 64-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 160 |
| 類型： | 定時卡 IC，多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum，電信 |
| 輸入： | CMOS，LVDS，LVPECL，TTL |
| 輸出： | CMOS，LVDS，LVPECL，TTL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 5:2 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 312.5MHz |
| 電源電壓： | 1.62 V ~ 1.98 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
DS3105
46
generators free-run with their existing 2kHz alignments. When the external frame sync is enabled and the SYNCn
signal is qualified, the FSYNC/MFSYNC 2kHz alignment generator is always synchronized by the SYNCn signal,
and, therefore, FSYNC and MFSYNC are always falling-edge aligned with SYNCn. When FSCR2:INDEP = 0, the
T0 DPLL 2kHz alignment generator is also synchronized with the FSYNC/MFSYNC 2kHz alignment generator to
falling-edge align all T0-derived output clocks with the SYNCn signal. When INDEP = 1, the T0 DPLL 2-kHz
alignment generator is not synchronized with the FSYNC/MFSYNC 2kHz alignment generator and continues to
free-run with its existing 2kHz alignment. This avoids any disturbance on the T0 DPLL derived output clocks when
the SYNCn signal has a change of phase position.
7.9.6 Frame-Sync Monitor
The frame-sync monitor signal OPSTATE:FSMON operates in two modes, depending on the setting of the enable
bit (MCR3:EFSEN).
When EFSEN = 1 (external frame sync enabled), the OPSTATE:FSMON bit is set when the SYNCn signal is not
qualified and cleared when SYNCn is qualified. If the SYNCn signal is disqualified, both 2kHz alignment generators
are immediately disconnected from SYNCn to avoid phase movement on the T0-derived outputs clocks. When
OPSTATE:FSMON is set, the latched status bit MSR3:FSMON is also set, which can cause an interrupt if enabled
in the IER3 register. If SYNCn immediately stabilizes at a new phase and proper frequency, it is requalified after 64
2kHz cycles (nominally 32ms). Unless system software intervenes, after the SYNCn signal is requalified the 2kHz
alignment generators will synchronize with SYNCn’s new phase alignment, causing a sudden phase movement on
the output clocks. System software can avoid this sudden phase movement on the output clocks by responding to
the FSMON interrupt within the 32ms window with appropriate action, which might include disabling external frame
sync (MCR3:EFSEN = 0) to prevent the resynchronization of the 2kHz alignment generators with SYNCn, forcing
the T0 DPLL into holdover (MCR1:T0STATE = 010) to avoid affecting the output clocks with any other phase hits,
and possibly even disabling the master timing card and promoting the slave timing card to master since the 2kHz
signal from the master should not have such phase movements.
When EFSEN = 0 (external frame sync disabled), OPSTATE:FSMON is set when the negative edge of the
resampled SYNCn signal is outside the window determined by FSCR3:MONLIM relative to the MFSYNC negative
edge (or positive edge if MFSYNC is inverted) and clear when within the window. When OPSTATE:FSMON is set,
the latched status bit MSR3:FSMON is also set, which can cause an interrupt if enabled in the IER3 register.
7.9.7 Other Configuration Options
FSYNC and MFSYNC are always produced from the T0 DPLL. The other output clocks can also be configured as
2kHz or 8kHz outputs, derived from the T0 DPLL.
7.10 Microprocessor Interface
The DS3105 presents an SPI interface on the
CS, SCLK, SDI, and SDO pins. SPI is a widely used master/slave
bus protocol that allows a master device and one or more slave devices to communicate over a serial bus. The
DS3105 is always a slave device. Masters are typically microprocessors, ASICs, or FPGAs. Data transfers are
always initiated by the master device, which also generates the SCLK signal. The DS3105 receives serial data on
the SDI pin and transmits serial data on the SDO pin. SDO is high impedance except when the DS3105 is
transmitting data to the bus master.
Bit Order. When both bit 3 and bit 4 are low at device address 3FFFh, the register address and all data bytes are
transmitted MSB first on both SDI and SDO. When either bit 3 or bit 4 is set to 1 at device address 3FFFh, the
register address and all data bytes are transmitted LSB first on both SDI and SDO. The reset default setting and
Motorola SPI convention is MSB first.
Clock Polarity and Phase. When CPOL = 0, SCLK is normally low and pulses high during bus transactions. The
CPHA pin sets the phase (active edge) of SCLK. When CPHA = 0, data is latched in on SDI on the leading edge of
the SCLK pulse and updated on SDO on the trailing edge. When CPHA = 1, data is latched in on SDI on the
trailing edge of the SCLK pulse and updated on SDO on the following leading edge. SCLK does not have to toggle
between accesses, i.e., when
CS is high. See Figure 7-4.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3106LN+ | IC TIMING LINE CARD 64-LQFP |
| DS3231MZ+ | IC RTC I2C 8SOIC |
| DS3231SN#T&R | IC RTC W/TCXO 16-SOIC |
| DS3232MZ+ | IC RTC W/SRAM I2C 8SOIC |
| DS3232SN#T&R | IC RTC W/TCXO 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3105LN+ | 功能描述:計時器和支持產品 Line Card Timing IC RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS3106 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Line Card Timing IC |
| DS3106A10SL3S(621) | 制造商:Amphenol Corporation 功能描述: |
| DS3106A14S2S | 制造商:Amphenol Corporation 功能描述: |
| DS3106A14S2S(621) | 制造商:Amphenol Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。