參數資料
型號: DS2760TA
英文描述: High Precision Li-Ion Battery Monitor
中文描述: 高精度鋰離子電池監視器
文件頁數: 10/25頁
文件大?。?/td> 126K
代理商: DS2760TA
DS2760
10 of 25
TEMPERATURE MEASUREMENT
The DS2760 uses an integrated temperature sensor to continually measure battery temperature.
Temperature measurements are placed in the Temperature Register in two’s-complement format with a
resolution of 0.125°C over a range of
±
127°C. The Temperature Register format is shown in Figure 8.
TEMPERATURE REGISTER FORMAT –
Figure 8
MSB—Address 18
LSB—Address 19
S
2
9
2
8
2
7
2
6
2
5
2
4
2
3
2
2
2
1
2
0
X
X
X
X
X
MSb
LSb
MSb
LSb
Units: 0.125
°
C
PROGRAMMABLE I/O
To use the PIO pin as an output, write the desired output value to the PIO bit in the Special Feature
Register. Writing a 0 to the PIO bit enables the PIO output driver, pulling the PIO pin to VSS. Writing a
1 to the PIO bit disables the output driver, allowing the PIO pin to be pulled high or used as an input. To
sense the value on the PIO pin, read the PIO bit. The DS2760 turns off the PIO output driver when in
enters Sleep Mode or when DQ is low for more than 2 seconds, regardless of the state of the PMOD bit.
POWER SWITCH INPUT
The DS2760 provides a power control function that uses the discharge protection FET to gate battery
power to the system. The
PS
pin, internally pulled to VDD through a 1
μ
A current source, is
continuously monitored for a low-impedance connection to VSS. If the DS2760 is in Sleep Mode, the
detection of a low on
PS
causes the device to transition into Active Mode, turning on the discharge FET.
If the DS2760 is already in Active Mode, activity on
PS
has no effect other than the mirroring of its logic
level in the
PS
bit in the Special Feature Register.
MEMORY
The DS2760 has a 256-byte linear address space with registers for instrumentation, status and control in
the lower 32 bytes, with lockable EEPROM and SRAM memory occupying portions of the remaining
address space. All EEPROM and SRAM memory is general-purpose except addresses 30h, 31h, and 33h,
which should be written with the default values for the Protection Register, Status Register, and Current
Offset Register, respectively. When the MSB of any 2 byte register is read, both the MSB and LSB are
latched and held for the duration of the Read Data command to prevent updates during the read and
ensure synchronization between the two register bytes. For consistent results, always read the MSB and
the LSB of a two-byte register during the same Read Data command sequence.
EEPROM memory is shadowed by RAM to eliminate programming delays between writes and to allow
the data to be verified by the host system before being copied to EEPROM. All reads and writes to/from
EEPROM memory actually access the shadow RAM. In unlocked EEPROM blocks, the Write Data
command updates shadow RAM. In locked EEPROM blocks, the Write Data command is ignored. The
Copy Data command copies the contents of shadow RAM to EEPROM in an unlocked block of
EEPROM but has no effect on locked blocks. The Recall Data command copies the contents of a block of
EEPROM to shadow RAM regardless of whether the block is locked or not.
相關PDF資料
PDF描述
DS2760X High Precision Li-Ion Battery Monitor
DS2760XA High Precision Li-Ion Battery Monitor
DS2770 Battery Monitor and Charge Controller
DS2770AE Battery Monitor and Charge Controller
DS2770AE-025 Battery Monitor and Charge Controller
相關代理商/技術參數
參數描述
DS2760TA-025 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High Precision Li-Ion Battery Monitor
DS2760X 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High Precision Li-Ion Battery Monitor
DS2760X-025 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High Precision Li-Ion Battery Monitor
DS2760XA 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High Precision Li-Ion Battery Monitor
DS2760XA-025 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High Precision Li-Ion Battery Monitor