- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2740BU High-Precision Coulomb Counter PDF資料下載
參數資料
| 型號： | DS2740BU |
| 元件分類： | 通用總線功能 |
| 英文描述： | High-Precision Coulomb Counter |
| 中文描述： | 高精度庫侖計 |
| 文件頁數： | 12/15頁 |
| 文件大?。?/td> | 248K |
| 代理商： | DS2740BU |
DS2740
12 of 15
Table 4.
FUNCTION COMMANDS
COMMAND
DESCRIPTION
COMMAND
PROTOCOL
BUS STATE
AFTER COMMAND
PROTOCOL
BUS DATA
Read Data
Reads data from
memory starting at
address XX
Writes data to memory
starting at address XX
69h, XX
Master Rx
Up to 256 bytes
of data
Write Data
6Ch, XX
Master Tx
Up to 256 bytes
of data
1-WIRE SIGNALING
The 1-Wire bus requires strict signaling protocols to ensure data integrity. The four protocols used by the
DS2740 are as follows: the initialization sequence (reset pulse followed by presence pulse), write 0, write
1, and read data. All of these types of signaling except the presence pulse are initiated by the bus master.
The initialization sequence required to begin any communication with the DS2740 is shown in Figure 11.
A presence pulse following a reset pulse indicates that the DS2740 is ready to accept a net address
command. The bus master transmits (Tx) a reset pulse for t
RSTL
. The bus master then releases the line and
goes into receive mode (Rx). The 1-Wire bus line is then pulled high by the pullup resistor. After
detecting the rising edge on the DQ pin, the DS2740 waits for t
PDH
and then transmits the presence pulse
for t
PDL
.
Figure 11.
1-WIRE INITIALIZATION SEQUENCE
WRITE-TIME SLOTS
A write-time slot is initiated when the bus master pulls the 1-Wire bus from a logic-high (inactive) level
to a logic-low level. There are two types of write-time slots: write 1 and write 0. All write-time slots must
be t
SLOT
in duration with a 1 s minimum recovery time, t
REC
, between cycles. The DS2740 samples the
1-Wire bus line between 15 s and 60 s (between 2 s and 6 s for overdrive speed) after the line falls. If
the line is high when sampled, a write 1 occurs. If the line is low when sampled, a write 0 occurs (see
Figure 12). For the bus master to generate a write 1 time slot, the bus line must be pulled low and then
released, allowing the line to be pulled high within 15 s (2 s for overdrive speed) after the start of the
write-time slot. For the host to generate a write 0 time slot, the bus line must be pulled low and held low
for the duration of the write-time slot.
t
RSTL
t
PDL
t
RSTH
t
PDH
PACK+
PACK-
LINE TYPE LEGEND:
BUS MASTER ACTIVE LOW
DS2740 ACTIVE LOW
RESISTOR PULLUP
BOTH BUS MASTER AND
DS2740 ACTIVE LOW
DQ
相關PDF資料 |
PDF描述 |
|---|---|
| DS2740U | High-Precision Coulomb Counter |
| DS2760E-025 | High Precision Li-Ion Battery Monitor |
| DS2760XA-025 | High Precision Li-Ion Battery Monitor |
| DS2760 | High Precision Li-Ion Battery Monitor |
| DS2760E | High Precision Li-Ion Battery Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2740BU/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Coulomb Counter |
| DS2740BU/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Coulomb Counter |
| DS2740BU/T&R | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2740BU+ | 功能描述:電池管理 High-Precision Coulomb Counter RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2740BU+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:HIPREC COULCNTR USOP8 LEAD FREE T&R 制造商:Maxim Integrated Products 功能描述:HIGH-PRECISION COULOMB COUNTER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CURRENT GAUGE(15BIT) 8UMAX 制造商:Maxim Integrated Products 功能描述:Battery Management High-Precision Coulomb Counter |
發布緊急采購，3分鐘左右您將得到回復。