- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2740B High-Precision Coulomb Counter PDF資料下載
參數資料
| 型號： | DS2740B |
| 元件分類： | 通用總線功能 |
| 英文描述： | High-Precision Coulomb Counter |
| 中文描述： | 高精度庫侖計 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 248K |
| 代理商： | DS2740B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
DS2740
8 of 15
CRC is available in Application Note 27,
Understanding and Using Cyclic Redundancy Checks with
Dallas Semiconductor Touch Memory Products
. (This application note can be found on the Maxim/Dallas
Semiconductor website at www.maxim-ic.com.)
In the circuit in Figure 8, the shift register bits are initialized to 0. Then, starting with the least significant
bit of the family code, one bit at a time is shifted in. After the 8th bit of the family code has been entered,
then the serial number is entered. After the 48th bit of the serial number has been entered, the shift
register contains the CRC value.
Figure 8.
1-WIRE CRC GENERATION BLOCK DIAGRAM
HARDWARE CONFIGURATION
Because the 1-Wire bus has only a single line, it is important that each device on the bus be able to drive
it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must connect to the
bus with open-drain or tri-state output drivers. The DS2740 uses an open-drain output driver as part of the
bidirectional interface circuitry shown in Figure 9. If a bidirectional pin is not available on the bus master,
separate output and input pins can be connected together.
The 1-Wire bus must have a pullup resistor at the bus-master end of the bus. For short line lengths, the
value of this resistor should be approximately 5k . The idle state for the 1-Wire bus is high. If, for any
reason, a bus transaction must be suspended, the bus must be left in the idle state to properly resume the
transaction later. If the bus is left low for more than 120 s (16 s for overdrive speed), slave devices on
the bus begin to interpret the low period as a reset pulse, effectively terminating the transaction.
The DS2740 can operate in two communication speed modes, standard and overdrive. The speed mode is
determined by the input logic level of the OVD pin with a logic 0 selecting standard speed and a logic 1
selecting overdrive speed. The OVD pin must be at a stable logic level of 0 or 1 before initializing a
transaction with a reset pulse. All 1-Wire devices on a multinode bus must operate at the same
communication speed for proper operation. 1-Wire timing for both standard and overdrive speeds are
listed in the
Electrical Characteristics: 1-Wire Interface
tables.
MSb
XOR
XOR
LSb
XOR
INPUT
相關PDF資料 |
PDF描述 |
|---|---|
| DS2740BU | High-Precision Coulomb Counter |
| DS2740U | High-Precision Coulomb Counter |
| DS2760E-025 | High Precision Li-Ion Battery Monitor |
| DS2760XA-025 | High Precision Li-Ion Battery Monitor |
| DS2760 | High Precision Li-Ion Battery Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2740BU | 制造商:Maxim Integrated Products 功能描述:HI PRECISION COUL CNTR USOP 8 PIN - Rail/Tube |
| DS2740BU/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Coulomb Counter |
| DS2740BU/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Precision Coulomb Counter |
| DS2740BU/T&R | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2740BU+ | 功能描述:電池管理 High-Precision Coulomb Counter RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。