- 您現在的位置：買賣IC網 > PDF目錄9751 > DS26324GN+ (Maxim Integrated Products)IC LIU 16CH T1/E1/J1 256CSBGA PDF資料下載
參數資料
| 型號： | DS26324GN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 41/120頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU 16CH T1/E1/J1 256CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 16/16 |
| 規程： | LIN |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 256-LBGA，CSBGA |
| 供應商設備封裝： | 256-CSBGA（17x17） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
DS26324 3.3V, 16-Channel, E1/T1/J1 Short-Haul Line Interface Unit
27 of 120
5.4.7
Transmit All Ones
When Transmit All Ones is invoked, continuous ones are transmitted using MCLK as the timing reference. Data
input at TPOS and TNEG is ignored.
Transmit All Ones can be sent by setting bits in the TAOE Register. Also, Transmit All Ones will be enabled if bits
5.4.8
Driver Fail Monitor
The Driver Fail Monitor is connected to the TTIP and TRING pins. It will detect a short or open circuit on the
secondary side of the transmit transformer. The drive current will be limited to 50mA if a short circuit is detected.
The DFMS status registers and the corresponding interrupt and enable registers can be used to monitor the driver
failure.
5.5
Receiver
The DS26324’s 16 receivers are all identical. A 1:2 or 1:1 transformer can be used on the receive side (selected by
the RTR bit), but only a 1:1 transformer can be used if fully internal impedance match is enabled. Fully internal
receive impdeance match does not require the use of any external resistor on the receive line. If partially internal
impdeance matching is selected, the DS26334 will need only an external 120
resistor (30 for a 1:2 transformer)
for E1, T1, and J1. The receive impedance match settings are controlled by the transmit template/impedance
selection. See Figure 5-8 and Table 5-5 for external component values. Partially internal impedance matching is
enabled via the TS.RIMPON bit. Fully internal impedance matching is enabled by setting GC.RIMPMS and
TS.RIMPON.
The peak detector and data slicer process the received signal. The output of the data slicer goes to clock and data
recovery. A 2.048/1.544 PLL is internally multiplied by 16 via another internal PLL and fed to the clock recovery
system derives E1 or T1 clock. The clock recovery system uses the clock from the PLL circuit to form a 16 times
oversampler, which is used to recover the clock and data. This oversampling technique offers outstanding
performance to meet jitter tolerance specifications.
B8ZS/HDB3/AMI decoding is available when single-rail mode is selected. The selection of single-rail or dual rail is
done by settings in the SRMS register.
The receiver is capable of recovering signals up to 18dB worth of attenuation. The receiver contains functionality to
provide resistive gain up to 20dB for monitor mode.
Three receive termination modes are available:
1) External Impedance Matching. Internal impedance matching is disabled, external resistor should match
line impedance.
2) Partially Internal Impedance Matching. Internal impedance matching is enabled, in parallel with an
external termination resistor (one value for all terminations).
3) Fully Internal Impedance Matching. Internal impedance matching is enabled, no external termination
necessary. This mode requires a 1:1 receive-side transformer.
5.5.1
Receiver Impedance Matching Calibration
In fully internal impedance matching mode, calibration of the internal resistors is necessary to match the line
impedance accurately. Calibration must be done upon power-up of the device. The resistance of the internal
resistors does vary across temperature. Therefore, it may be necessary to recalibrate if the ambient temperature
changes more than 30
°C. The user may conclude that it is necessary to recalibrate on a periodic basis if he
expects such temperature swings. Calibration is not necessary for partially internal impedance match mode.
5.5.2
Receiver Monitor Mode
The receive equalizer is equipped with monitor mode function that allows for resistive gain up to 20dB, along with
cable attenuation of 6dB to 24dB as shown in the RSMM1–4 registers.
相關PDF資料 |
PDF描述 |
|---|---|
| MC100EP116MNG | IC LINE RCVR/DRVR HEX DIFF 32QFN |
| M83723/72W1020N | CONN RCPT 2POS WALL MT W/PINS |
| M83723/72R1020N | CONN RCPT 2POS WALL MT W/PINS |
| DS3152N+ | IC LIU DS3/E3/STS-1 144-CSBGA |
| VI-260-IU-F2 | CONVERTER MOD DC/DC 5V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26324GN+ | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GN+T&R | 制造商:Maxim Integrated Products 功能描述:X16 T1E1J1 S-H LIU CSBGA IND LF T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LIU E1/T1/J1 3.3V 256-CSBGA |
| DS26324GN+T&R | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GNA2 | 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GNA2+ | 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。