參數資料
型號： DS2490S
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Bus Controller
英文描述： UNIVERSAL SERIAL BUS CONTROLLER, PDSO24
封裝： 0.300 INCH, SO-24
文件頁數： 24/51頁
文件大小： 444K
代理商： DS2490S
DS2490
30 of 50
DEVICE FEEDBACK
DS2490 state and result feedback are provided to the host over the EP1 interrupt pipe. The host interrupt
polling period for EP1 transfers is controlled by the alternate setting of the 1-Wire USB Interface as
described in the section: 1-Wire Interface Summary Description. As shown in Table 16, up to 32 bytes of
feedback data are returned. As a minimum, 16 bytes of STATE REGISTER data will be delivered at each
polling interval (or USB IN transaction to EP1); the position and definition of these data values are listed
in Table 17. In addition, as shown in Table 18, between 0 and 16 extra bytes of RESULT REGISTER
data will be delivered with feedback data. This consists of communication command processing result
data as controlled by the embedded communication command bits ICP and NTF and notification bytes for
1-Wire device arrival detection. If there are less than 32 bytes of result and state register data to return,
the DS2490 will terminate the IN transaction with a short or zero data packet.
Data is loaded into the RESULT REGISTER buffer based on embedded communication command bits
NTF and ICP or upon detection of a 1-Wire device attachment. There is no defined offset position for
data values in this buffer. Knowledge of communication command ordering sent to the DS2490 must be
maintained on the host to properly interpret the returned data values. In addition, a parse of the data is
required to determine whether or not a 1-Wire detect value is included; the value of the 1-Wire detect
byte is unique. Table 19 defines the 1-Wire detect byte and data values that result from Communication
command processing.
Interrupt Transfer Data Summary Table 16
OFFSET
DATA
0x00 to 0x0F
STATE REGISTERS
0x10 to 0x1F1
RESULT REGISTERS
Notes:
1. The number of RESULT RESIGTER values will vary depending on the setting of embedded
communication command bits NTF and ICP, the number of communication commands processed
since the previous EP1 polling period, or whether a 1-Wire device was detected.
DS2490 STATE REGISTERS Table 17
Description
Offset
Data
Enable Flags
0x00
bit7 bit6 bit5
bit4
bit3
bit2
bit1
bit0
--
SPCE
PRGE
SPUE
SPUE If set to 1, the strong pullup to 5V is enabled, if set to 0,
it is disabled.
PRGE If set to 1, a 12V programming pulse is enabled, if set to
0, it is disabled.
SPCE If set to 1, a dynamic 1-Wire bus speed change through a
Communication command is enabled, if set to 0, it is
disabled.
bit 3..7 These bits are reserved.
1-Wire Speed
0x01
current 1-Wire bus speed code
Strong Pullup Duration
0x02
current pullup duration
Programming Pulse
0x03
current programming pulse duration
相關PDF資料
PDF描述
DS2502P 128 X 8 OTPROM, PDSO6
DS2502S 128 X 8 OTPROM, PDSO8
DS2502 128 X 8 OTPROM, PBCY3
DS2505/T&R 16K X 1 OTPROM, PBCY3
DS2505P 16K X 1 OTPROM, PDSO6
相關代理商/技術參數
參數描述
DS2490S+ 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Rail/Tube 制造商:Maxim Integrated Products 功能描述:USB 1-W BRIDGE CHIP 24-SO LF 制造商:Maxim Integrated Products 功能描述:Bulk
DS2490S+T&R 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Tape and Reel
DS2490S+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:USB to 1-Wire Bridge Chip
DS2490X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB to 1-Wire Bridge Chip(468.41 k)
DS2490X/T&R 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*