參數資料
型號: DS2438
英文描述: Smart Battery Monitor
中文描述: 智能電池監視器
文件頁數: 21/29頁
文件大?。?/td> 351K
代理商: DS2438
DS2438
21 of 29
Recall Memory [B8hxxh]
This command recalls the stored values in EEPROM / SRAM page xxh to the scratchpad page xxh. This
command must proceed a Read SPxx command in order to read any page of memory on the DS2438.
Valid page numbers are 00h - 07h.
Convert T [44h]
This command begins a temperature conversion. No further data is required. The temperature conversion
will be performed, setting the TB flag in the Status/Configuration register to a “1” during conversion.
When the temperature conversion is done, the TB flag will clear to a “0”. If the bus master issues read
time slots following this command, the DS2438 will output “0” on the bus as long as it is busy making a
temperature conversion; it will return a “1” when the temperature conversion is complete.
Convert V [B4h]
This command instructs the DS2438 to initiate a voltage analog-to-digital conversion cycle. This sets the
ADB flag (see Status/Configuration register discussion in the Memory Map section). The voltage supply
that is measured is defined by the AD bit of the Status/Configuration register. When the A/D conversion
is done, the ADB flag is cleared and the current voltage value is placed in the VOLTAGE REGISTER of
page 00h. While an A/D conversion is taking place, all other memory functions are still available for use.
If the bus master issues read time slots following this command, the DS2438 will output “0” on the bus as
long as it is busy making a voltage measurement; it will return a “1” when the conversion is complete.
DS2438 COMMAND SET
Table 11
INSTRUCTION
DESCRIPTION
PROTOCOL
1-WIRE BUS
MASTER STATUS
AFTER ISSUING
PROTOCOL
1-WIRE BUS
DATA AFTER
ISSUING
PROTOCOL
MEMORY COMMANDS
BEh <page
00h-07h>
Read Scratchpad
Reads bytes from
DS2438 Scratchpad
page xxh
Writes bytes to
DS2438
Scratchpad page xxh
Rx
<read up to nine
bytes of data>
Write Scratchpad
4Eh <page
00h-07h>
Tx
<write up to eight
bytes of data>
Copy Scratchpad
Copies entire contents
of Scratchpad page
xxh
to 8-byte EEPROM/
SRAM page xxh
Copies entire contents
of EEPROM/SRAM
page xxh to
Scratchpad
page xxh
48h<page
00h-07h>
Idle or Rx of NVB bit
{NVB bit in Status
Register = 1 until
copy complete (2-
10 ms, typ)}
Recall Memory
B8h<page
00h-07h>
Idle
Idle
REGISTER COMMANDS
44h
Convert T
Initiates temperature
conversion
Idle or Rx of TB bit
{TB bit in Status
Register = 1 until
conversion
complete}
{ADB bit in Status
Register = 1 until
conversion
complete}
Convert V
Initiates voltage A/D
conversion
B4h
Idle or Rx of ADB bit
相關PDF資料
PDF描述
DS2438Z Smart Battery Monitor
DS2442 Battery Management
DS2501 1A VERY LOW DROPOUT VOLTAGE REGULATORS
DS2502 1 kbit Add-Only Memory
DS2502P-E48 48-Bit Node Address Chip
相關代理商/技術參數
參數描述
DS2438AZ 功能描述:IC MONITOR SMART BATTERY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子(Li-Ion)、鋰聚合物(Li-Pol) 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A,SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
DS2438AZ/T&R 制造商:Maxim Integrated Products 功能描述:SMART BATTERY MONITOR 8-SOIC/T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 8-SOIC
DS2438AZ/T&R 功能描述:IC MONITOR SMART BATTERY 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子(Li-Ion)、鋰聚合物(Li-Pol) 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A,SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
DS2438AZ+ 功能描述:電池管理 Smart Battery Monitor RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
DS2438AZ+ 制造商:Maxim Integrated Products 功能描述:IC BATTERY MONITOR LI-ION 10V SOIC-8