- 您現在的位置：買賣IC網 > PDF目錄97869 > DS2436B (DALLAS SEMICONDUCTOR) SPECIALTY MEMORY CIRCUIT, PBCY3 PDF資料下載
參數資料
| 型號： | DS2436B |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Memory IC:Other |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBCY3 |
| 封裝： | TO-92, 3 PIN |
| 文件頁數： | 8/29頁 |
| 文件大?。?/td> | 505K |
| 代理商： | DS2436B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
DS2436
16 of 29
1-WIRE CRC CODE Figure 6
1-WIRE BUS SYSTEM
The 1-Wire bus is a system which has a single bus master and one or more slaves. The DS2436 behaves
as a slave. All data is communicated LSB first. The discussion of this bus system is broken down into
three topics: hardware configuration, transaction sequence, and 1-Wire signaling (signal types and
timing).
HARDWARE CONFIGURATION
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open
drain or three-state outputs. The 1-Wire port of the DS2436 (DQ pin) is open drain with an internal circuit
equivalent to that shown in Figure 7. A multidrop bus consists of a 1-Wire bus with multiple slaves
attached. The 1-Wire bus requires a pullup resistor of approximately 5 k
.
The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus
MUST be left in the idle state for the transaction to resume. Infinite recovery time can occur between bits
so long as the 1-Wire bus is in the inactive (HIGH) state during the recovery period. If this does not occur
and the bus is left low for more than 480
s, all components on the bus will be reset.
TRANSACTION SEQUENCE
The protocol for accessing the DS2436 via the 1-Wire port is as follows:
§ Initialization
§ ROM Function Command
§ Memory Function Command
§ Transaction/Data
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the
slave(s).
The presence pulse lets the bus master know that the DS2436 is on the bus and is ready to operate. For
more details, see the “1-Wire Signaling” section.
ROM FUNCTION COMMANDS
Once the bus master has detected a presence, it can issue one of the four ROM function commands. All
ROM function commands are 8 bits long. A list of these commands follows (refer to flowchart in Figure
5).
相關PDF資料 |
PDF描述 |
|---|---|
| DS2436Z | SPECIALTY MEMORY CIRCUIT, PDSO8 |
| DS2490S | UNIVERSAL SERIAL BUS CONTROLLER, PDSO24 |
| DS2502P | 128 X 8 OTPROM, PDSO6 |
| DS2502S | 128 X 8 OTPROM, PDSO8 |
| DS2502 | 128 X 8 OTPROM, PBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2436B/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery ID/Monitor Chip |
| DS2436B/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Battery ID/Monitor Chip |
| DS2436B/T&R | 制造商:Maxim Integrated Products 功能描述:BATTERY MONITOR TO-92 T&R - Tape and Reel |
| DS2436B/T&R | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2436B+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。