- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2430AX (DALLAS SEMICONDUCTOR) 32 X 8 1-WIRE SERIAL EEPROM, UUC2 PDF資料下載
參數資料
| 型號： | DS2430AX |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Programmable ROM |
| 英文描述： | 32 X 8 1-WIRE SERIAL EEPROM, UUC2 |
| 封裝： | CSP-2 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 357K |
| 代理商： | DS2430AX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
DS2430A
6 of 16
102199
MEMORY FUNCTION FLOW CHART Figure 6
COPY SCRATCHPAD [55h]
After the data stored in the scratchpad has been verified the master may send the Copy Scratchpad
command followed by a validation key of A5h to transfer data from the scratchpad to the EEPROM
memory. This command will always copy the data of the entire scratchpad. Therefore, if one desires to
change only a few bytes of the EEPROM data, the scratchpad should contain a copy of the latest
EEPROM data before the Write Scratchpad and Copy Scratchpad commands are issued. After this
command is issued, the data line must be held at logic high level for at least 10 ms.
READ MEMORY [F0h]
The Read Memory command is used to read a portion or all of the EEPROM data memory and to copy
the entire data memory into the scratchpad to prepare for changing a few bytes. To copy data from the
data memory to the scratchpad and to read it, the master must issue the read memory command followed
by the 1-byte starting address from where data is to be read from the scratchpad. The DS2430A will
automatically increment the address after every byte read by the master. After the data of address 1Fh has
been read, the address counter will wrap around to 00h for the next byte and reading continues until the
master sends a reset pulse. If one intends to copy the entire data memory to the scratchpad without
reading data, a starting address is not required; the master may send a reset pulse immediately following
the command code.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2432P/T&R | 1K X 1 1-WIRE SERIAL EEPROM, PDSO6 |
| DS2432X | 1K X 1 1-WIRE SERIAL EEPROM, PBGA6 |
| DS2432P | 1K X 1 1-WIRE SERIAL EEPROM, PDSO6 |
| DS2433 | 512 X 8 1-WIRE SERIAL EEPROM, PBCY3 |
| DS2433X | 4K X 1 1-WIRE SERIAL EEPROM, UUC2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2430AX#T&R | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| DS2430AX#U | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| DS2430AX-S | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| DS2430AX-S#T&R | 制造商:Maxim Integrated Products 功能描述: |
| DS2430AX-S#T&R | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。