- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2430AP (MAXIM INTEGRATED PRODUCTS INC) 256 X 1 1-WIRE SERIAL EEPROM, PDSO6 PDF資料下載
參數資料
| 型號： | DS2430AP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Programmable ROM |
| 英文描述： | 256 X 1 1-WIRE SERIAL EEPROM, PDSO6 |
| 封裝： | 3.70 X 4 MM, 1.50 MM HEIGHT, TSOC-6 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 1683K |
| 代理商： | DS2430AP |
DS2430A
5 of 16
MEMORY
The memory of the DS2430A consists of three separate sections, called data memory, application
register, and status register (Figure 5). The data memory and the application register each have its own
intermediate storage area called scratchpad that acts as a buffer when writing to the device. The data
memory can be read and written as often as desired. The application register, however, is one-time
programmable only. Once the application register is programmed, it is automatically write protected. The
status register will indicate if the application register is already locked or if it is still available for storing
data. As long as the application register is unprogrammed, the status register will read FFh. Copying data
from the register scratchpad to the application register will clear the 2 least significant bits of the status
register, yielding an FCh the next time one reads the status register.
DS2430A MEMORY MAP Figure 5
MEMORY FUNCTION COMMANDS
The Memory Function Flow Chart (Figure 6) describes the protocols necessary for accessing the different
memory sections of the DS2430A. An example is shown later in this document.
WRITE SCRATCHPAD [0Fh]
After issuing the Write Scratchpad command, the master must first provide a 1-byte address, followed by
the data to be written to the scratchpad for the data memory. The DS2430A will automatically increment
the address after every byte it received. After having received a data byte for address 1Fh, the address
counter will wrap around to 00h for the next byte and writing continues until the master sends a Reset
Pulse.
READ SCRATCHPAD [AAh]
This command is used to verify data previously written to the scratchpad before it is copied into the final
storage EEPROM memory. After issuing the Read Scratchpad command, the master must provide the 1-
byte starting address from where data is to be read. The DS2430A will automatically increment the
address after every byte read by the master. After the data of address 1Fh has been read, the address
counter will wrap around to 00h for the next byte and reading continues until the master sends a Reset
Pulse.
Not
Recommended
for
New
Design
相關PDF資料 |
PDF描述 |
|---|---|
| DS2430A | 32 X 8 1-WIRE SERIAL EEPROM, PBCY3 |
| DS2430AX | 32 X 8 1-WIRE SERIAL EEPROM, UUC2 |
| DS2432P/T&R | 1K X 1 1-WIRE SERIAL EEPROM, PDSO6 |
| DS2432X | 1K X 1 1-WIRE SERIAL EEPROM, PBGA6 |
| DS2432P | 1K X 1 1-WIRE SERIAL EEPROM, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2430AP R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:256-Bit 1-Wire EEPROM |
| DS2430AP/T&R | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。