- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2422S 1-Wire Temperature/Datalogger with 8kB Datalog Memory PDF資料下載
參數資料
| 型號： | DS2422S |
| 英文描述： | 1-Wire Temperature/Datalogger with 8kB Datalog Memory |
| 中文描述： | 1 - Wire溫度/數據記錄器與8kB的數據記錄存儲器 |
| 文件頁數： | 25/48頁 |
| 文件大?。?/td> | 444K |
| 代理商： | DS2422S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
DS2422
25 of 48
If there is a risk of unauthorized access to the DS2422 or manipulation of data, one should define passwords for
read access and full access. Before the passwords become effective, their use needs to be enabled.
See Security
by Password
for more details.
The last step to begin a mission is to issue the Start Mission command. As soon as it has received this command,
the DS2422 sets the MIP flag and clear the MEMCLR flag. With the immediate/delayed start mode (SUTA = 0),
after as many minutes as specified by the Mission Start Delay are over, the device wakes up, copy the current date
and time to the mission time stamp register, and log the first entry of the mission. This increments both the Mission
Samples Counter and Device Samples Counter. All subsequent log entries are made as specified by the value in
the Sample Rate Register and the EHSS bit.
If the Start Upon Temperature Alarm mode is chosen (SUTA = 1
,
ETL = 1) the DS2422 will first wait until the start
delay is over. Then the device wakes up in intervals as specified by the sample rate and EHSS bit and measure the
temperature. This increments the device samples counter only. Only after an alarming temperature is encountered
does the DS2422 set the mission time stamp. The first sample of the mission is logged one sample period after the
temperature alarm occurred.
From then on, both the Mission Samples Counter and Device Samples Counter
increments at the same time. All subsequent log entries are made as specified by the value in the Sample Rate
Register and the EHSS bit.
The general-purpose memory operates independently of the other memory sections and is not write-protected
during a mission. All memory of the DS2422 can be read at any time, e. g., to watch the progress of a mission.
Attempts to read the passwords will read 00h bytes instead of the data that is stored in the password registers.
ADDRESS REGISTERS AND TRANSFER STATUS
Because of the serial data transfer, the DS2422 employs three address registers, called TA1, TA2, and E/S (Figure
11). Registers TA1 and TA2 must be loaded with the target address to which the data is written or from which data
is sent to the master upon a Read command. Register E/S acts like a byte counter and transfer status register. It is
used to verify data integrity with Write commands. Therefore, the master only has read access to this register. The
lower 5 bits of the E/S Register indicate the address of the last byte that has been written to the scratchpad. This
address is called Ending Offset.
The DS2422 requires that the Ending Offset is always 1Fh for a Copy
Scratchpad to function.
Bit 5 of the E/S Register, called PF or “partial byte flag,” is set if the number of data bits
sent by the master is not an integer multiple of 8. Bit 6 is always a 0. Note that the lowest 5 bits of the target
address also determine the address within the scratchpad, where intermediate storage of data will begin. This
address is called byte offset. If the target address for a Write command is 13Ch, for example, then the scratchpad
will store incoming data beginning at the byte offset 1Ch and will be full after only 4 bytes. The corresponding
ending offset in this example is 1Fh. For best economy of speed and efficiency, the target address for writing
should point to the beginning of a new page, i.e., the byte offset will be 0. Thus the full 32-byte capacity of the
scratchpad is available, resulting also in the ending offset of 1Fh. However, it is possible to write 1 or several
contiguous bytes somewhere within a page. The ending offset together with the Partial and Overflow Flag is mainly
a means to support the master checking the data integrity after a Write command. The highest valued bit of the E/S
Register, called AA or Authorization Accepted, indicates that a valid copy command for the scratchpad has been
received and executed. Writing data to the scratchpad clears this flag.
Figure 11. Address Registers
Bit #
7
6
5
4
3
2
1
0
Target Address (TA1)
T7
T6
T5
T4
T3
T2
T1
T0
Target Address (TA2)
T15
T14
T13
T12
T11
T10
T9
T8
Ending Address with
Data Status (E/S)
(Read Only)
AA
0
PF
E4
E3
E2
E1
E0
相關PDF資料 |
PDF描述 |
|---|---|
| DS2482-800 | Eight-Channel 1-Wire Master |
| DS2482-100 | Single-Channel 1-Wire Master |
| DS2482S-100 | Single-Channel 1-Wire Master |
| DS2482S-800 | Eight-Channel 1-Wire Master |
| DS2502-E48 | 48-Bit Node Address Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2422S+ | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS2422X | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS2423 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:4kbit 1-Wire RAM with Counter |
| DS2423D/T&R | 制造商:Maxim Integrated Products 功能描述:IC SRAM 4KBIT 6FLIPCHIP |
| DS2423D/T&R | 功能描述:IC SRAM 4KBIT 6FCHIP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:150 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (2 x 256 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-VFDFN 裸露焊盤 供應商設備封裝:8-DFN（2x3） 包裝:管件 產品目錄頁面:1445 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。