- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2409P (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY TELECOM CIRCUIT, PDSO6 PDF資料下載
參數資料
| 型號： | DS2409P |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Telecom IC:Other |
| 英文描述： | SPECIALTY TELECOM CIRCUIT, PDSO6 |
| 封裝： | 3.70 X 4 MM, 1.50 MM HEIGHT, TSOC-6 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 420K |
| 代理商： | DS2409P |
DS2409
5 of 18
STATUS CONTROL BYTE Table 1
765432
1
0
DATA
X
CNTR.
SEL.
MODE
R/ W
XX
X
0-2
X
don’t care
3-4
R/ W
Write control: both bits must be 0 to change the status.
5
MODE
control output mode selection: 0 = auto-control mode (default), 1 = manual mode
6
CNTR.
SEL.
control output association (auto-control mode): 0 = main (default), 1 = auxiliary
7
DATA
X
Value to be written to control output (manual mode only): don’t care otherwise
STATUS INFO BYTE Table 2
765432
1
0
MODE
CNTR.
STAT
EVNT
AUX.
EVNT
MAIN
AUX.
LEVL
AUX.
STAT
MAIN
LEVL
MAIN
STAT
0
MAIN
STAT
status of main output: 0 = active (connected to bus master), 1 = inactive
1
MAIN
LEVL
voltage sensed at main output: 0 = low, 1 = high (see note)
2
AUX.
STAT
status of auxiliary output: 0 = active (connected to bus master), 1 = inactive
3
AUX.
LEVL
voltage sensed at auxiliary output: 0 = low, 1 = high (see note)
4
EVNT
MAIN
event flag for main output: 0 = no event, 1 = negative edge sensed since inactive
5
EVNT
AUX.
event flag for aux. Output: 0 = no event, 1 = negative edge sensed since inactive
6
CNTR.
STAT
if auto-control mode: control output association, 0 = main, 1 = auxiliary
if manual mode: 0 = output transistor off, 1 = output transistor on
7
MODE
control output mode: 0 = auto-control mode, 1 = manual mode
NOTE:
Data is valid only if the output is decoupled from the 1-Wire input.
ALL LINES OFF [66h]
This command is used to deactivate the currently active 1-Wire output and to clear both event flags or to
end a discharge cycle initiated by the Discharge Lines command. Before issuing this command, one
should read the status and check the event flags of both, the main and the auxiliary output. Otherwise one
might inadvertently clear the event flag without having taken appropriate action. If the DS2409 is in auto-
control mode, the transistor at the control output will be switched off (non-conducting). At power-on, the
device will automatically perform the All Lines Off command. In contrast to a power-on cycle, the All
Lines Off command does not clear the Mode and Control Select bits.
Not
Recommended
for
New
Design
相關PDF資料 |
PDF描述 |
|---|---|
| DS2415P | 0 TIMER(S), REAL TIME CLOCK, PDSO6 |
| DS2415X | 0 TIMER(S), REAL TIME CLOCK, X6 |
| DS2417X | 0 TIMER(S), REAL TIME CLOCK, PBGA6 |
| DS2417P | 0 TIMER(S), REAL TIME CLOCK, PDSO6 |
| DS2422X | SPECIALTY MEMORY CIRCUIT, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2409P/T&R | 制造商:Maxim Integrated Products 功能描述:IC COUPLER MICROLAN 1-WIRE 6TSOC |
| DS2409P/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2409P+ | 制造商:Maxim Integrated Products 功能描述:MICROLAN COUPLER 制造商:Maxim Integrated Products 功能描述:MICROLAN COUPLER SMD TSOC-6 2409 |
| DS2411 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Silicon Serial Number with Vcc Input |
| DS2411C/W | 制造商:Maxim Integrated Products 功能描述:SINGLE, UNSORTED UN-BACKLAPPED WAFER - Gel-pak, waffle pack, wafer, diced wafer on film |
發布緊急采購，3分鐘左右您將得到回復。