- 您現在的位置：買賣IC網 > PDF目錄379183 > DS2409P MicroLAN Coupler PDF資料下載
參數資料
| 型號： | DS2409P |
| 英文描述： | MicroLAN Coupler |
| 中文描述： | 微型局域網耦合器 |
| 文件頁數： | 5/18頁 |
| 文件大?。?/td> | 415K |
| 代理商： | DS2409P |
DS2409
102199
5 of 18
STATUS CONTROL BYTE
Table 1
7
6
DATA
X
SEL.
5
4
3
2
1
0
CNTR.
MODE
R/
W
R/
W
X
X
X
0-2
3-4
5
X
don’t care
Write control: both bits must be 0 to change the status.
control output mode selection: 0 = auto-control mode (default), 1 = manual mode
R/
W
MODE
CNTR.
SEL.
DATA
X
6
control output association (auto-control mode): 0 = main (default), 1 = auxiliary
7
Value to be written to control output (manual mode only): don’t care otherwise
STATUS INFO BYTE
Table 2
7
CNTR.
STAT
6
5
4
3
2
1
0
MODE
EVNT
AUX.
EVNT
MAIN
AUX.
LEVL
AUX.
STAT
MAIN
LEVL
MAIN
STAT
0
MAIN
STAT
MAIN
LEVL
AUX.
STAT
AUX.
LEVL
EVNT
MAIN
EVNT
AUX.
CNTR.
STAT
MODE
status of main output: 0 = active (connected to bus master), 1 = inactive
1
voltage sensed at main output: 0 = low, 1 = high
(see note)
2
status of auxiliary output: 0 = active (connected to bus master), 1 = inactive
3
voltage sensed at auxiliary output: 0 = low, 1 = high
(see note)
4
event flag for main output: 0 = no event, 1 = negative edge sensed since inactive
5
event flag for aux. Output: 0 = no event, 1 = negative edge sensed since inactive
6
if auto-control mode: control output association, 0 = main, 1 = auxiliary
if manual mode: 0 = output transistor off, 1 = output transistor on
control output mode: 0 = auto-control mode, 1 = manual mode
7
Note:
Data is valid only if the output is decoupled from the 1-Wire input.
ALL LINES OFF [66h]
This command is used to deactivate the currently active 1-Wire output and to clear both event flags or to
end a discharge cycle initiated by the Discharge Lines command. Before issuing this command, one
should read the status and check the event flags of both, the main and the auxiliary output. Otherwise one
might inadvertently clear the event flag without having taken appropriate action. If the DS2409 is in auto-
control mode, the transistor at the control output will be switched off (non-conducting). At power-on, the
device will automatically perform the All Lines Off command. In contrast to a power-on cycle, the All
Lines Off command does not clear the Mode and Control Select bits.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2422 | 1-Wire Temperature/Datalogger with 8kB Datalog Memory |
| DS2422S | 1-Wire Temperature/Datalogger with 8kB Datalog Memory |
| DS2482-800 | Eight-Channel 1-Wire Master |
| DS2482-100 | Single-Channel 1-Wire Master |
| DS2482S-100 | Single-Channel 1-Wire Master |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2409P/T&R | 制造商:Maxim Integrated Products 功能描述:IC COUPLER MICROLAN 1-WIRE 6TSOC |
| DS2409P/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2409P+ | 制造商:Maxim Integrated Products 功能描述:MICROLAN COUPLER 制造商:Maxim Integrated Products 功能描述:MICROLAN COUPLER SMD TSOC-6 2409 |
| DS2411 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Silicon Serial Number with Vcc Input |
| DS2411C/W | 制造商:Maxim Integrated Products 功能描述:SINGLE, UNSORTED UN-BACKLAPPED WAFER - Gel-pak, waffle pack, wafer, diced wafer on film |
發布緊急采購，3分鐘左右您將得到回復。