- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2409P/T&R (Maxim Integrated Products)IC COUPLER MICROLAN 1-WIRE 6TSOC PDF資料下載
參數資料
| 型號： | DS2409P/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 18/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COUPLER MICROLAN 1-WIRE 6TSOC |
| 標準包裝： | 4,000 |
| 接口： | 1 線 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 封裝/外殼： | 6-LSOJ |
| 供應商設備封裝： | 6-TSOC |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
DS2409
9 of 18
HARDWARE CONFIGURATION Figure 6
1-WIRE BUS SYSTEM
The 1-Wire bus is a system which has a single bus master and one or more slaves. In all instances the
DS2409 behaves as a slave. The discussion of this bus system is broken down into three topics: hardware
configuration, transaction sequence, and 1-Wire signaling (signal types and timing). A 1-Wire protocol
defines bus transactions in terms of the bus state during specified time slots that are initiated on the
falling edge of sync pulses from the bus master. For a more detailed protocol description, refer to Chapter
4 of the Book of DS19xx iButton Standards.
Hardware Configuration
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open-
drain or 3-state outputs. The 1-Wire input of the DS2409 is open drain with an internal circuit equivalent
to that shown in Figure 6. A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The 1-
Wire bus has a maximum data rate of 16.3kbits per second and requires a pullup resistor of approximately
1.5k or a DS2480 driver for MicroLAN applications.
The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus
MUST be left in the idle state if the transaction is to resume. If this does not occur and the bus is left low
for more than 120s, one or more of the devices on the bus may be reset. The DS2409 may perform a
power-on reset cycle and deactivate both 1-Wire outputs if the 1-Wire input is low for minimum 8ms. A
low time of 12ms or more will always cause a power-on reset cycle.
Transaction Sequence
The protocol for accessing the DS2409 via the 1-Wire port is as follows:
§ Initialization
§ ROM Function Command
§ Control Function Command
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the
slave(s). The presence pulse lets the bus master know that the DS2409 is on the bus and is ready to
operate. For more details, see the “1-Wire Signaling” section.
Not
Recommended
for
New
Design
相關PDF資料 |
PDF描述 |
|---|---|
| DS2411P+T&R | IC SILICON SERIAL NUMBER 6TSOC |
| DS2413Q+T&R | IC SWITCH 2CH ADDRESS 6-TDFN |
| DS2480B+ | IC LINE DRVR W/SENSOR 1-W 8-SOIC |
| DS2482X-100+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2482X-101+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2411 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Silicon Serial Number with Vcc Input |
| DS2411C/W | 制造商:Maxim Integrated Products 功能描述:SINGLE, UNSORTED UN-BACKLAPPED WAFER - Gel-pak, waffle pack, wafer, diced wafer on film |
| DS2411MP000 | 制造商:Thomas & Betts 功能描述:200A,PLG,3P4W,MG,411,220V,400HZ |
| DS2411P | 功能描述:序列號注冊 RoHS:否 制造商:Maxim Integrated 數據總線寬度: 電源電壓-最大: 電源電壓-最小: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: |
| DS2411P/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Silicon Serial Number with VCC Input |
發布緊急采購，3分鐘左右您將得到回復。