參數資料
型號: DS232AS
廠商: DALLAS SEMICONDUCTOR
元件分類: Line Driver or Receiver
英文描述: LINE TRANSCEIVER, PDSO16
封裝: 0.300 INCH, SOIC-16
文件頁數: 16/28頁
文件大?。?/td> 581K
代理商: DS232AS
MAX15023
Wide 4.5V to 28V Input, Dual-Output
Synchronous Buck Controller
23
Maxim Integrated
To estimate the temperature rise of the die, use the fol-
lowing equation:
TJ = TA + (PT x
θJA)
where
θJA is the junction-to-ambient thermal resistance
of the package, PT is power dissipated in the device,
and TA is the ambient temperature. The
θJA is 36°C/W
for the 24-pin TQFN package on multilayer boards, with
the conditions specified by the respective JEDEC stan-
dards (JESD51-5, JESD51-7). If actual operating condi-
tions significantly deviate from those described in the
JEDEC standards, then an accurate estimation of the
junction temperature requires a direct measurement of
the case temperature (TC). Then, the junction tempera-
ture can be calculated using the following equation:
TJ = TC + (PT x
θJC)
Use 3°C/W as
θJC thermal resistance for the 24-pin
TQFN package. The case-to-ambient thermal resis-
tance (
θCA) is dependent on how well the heat is trans-
ferred from the PCB to the ambient. Therefore, solder
the exposed pad of the TQFN package to a large cop-
per area to spread heat through the board surface,
minimizing the case-to-ambient thermal resistance. Use
large copper areas to keep the PCB temperature low.
Boost Flying-Capacitor Selection
The MAX15023 uses a bootstrap circuit to generate the
necessary gate-to-source voltage to turn on the high-
side MOSFET. The selected n-channel high-side MOS-
FET determines the appropriate boost capacitance
values (CBST_in Typical Application Circuits) according
to the following equation:
where Qg is the total gate charge of the high-side
MOSFET and
VBST_ is the voltage variation allowed on
the high-side MOSFET driver after turn-on. Choose
VBST_ such that the available gate drive voltage is not
significantly degraded (e.g.,
VBST_ = 100mV to
300mV) when determining CBST_. The boost flying-
capacitor should be a low-ESR ceramic capacitor. A
minimum value of 100nF is recommended.
Applications Information
PCB Layout Guidelines
Make the controller ground connections as follows: cre-
ate a small analog ground plane near the IC or use a
dedicated internal plane. Connect this plane to SGND
and use this plane for the ground connection for the IN
bypass capacitor, compensation components, feed-
back dividers, RT resistor, and LIM_ resistors.
If possible, place all power components on the top side
of the board, and run the power stage currents (espe-
cially the one having large high-frequency components)
using traces or copper fills on the top side only, without
adding vias.
On the top side, lay out a large PGND copper area for
the output of channels 1 and 2, and connect the bottom
terminals of the high-frequency input capacitors, output
capacitors, and the source terminals of the low-side
MOSFETs to that area.
Then, make a star connection of the SGND plane to the
top copper PGND area with few vias in the vicinity of
the source terminal sensing. Do not connect PGND and
SGND anywhere else. Refer to the MAX15023
Evaluation Kit data sheet for guidance.
Keep the power traces and load connections short,
especially at the ground terminals. This practice is
essential for high efficiency and jitter-free operation. Use
thick copper PCBs (2oz vs. 1oz) to enhance efficiency.
Place the controller IC adjacent to the synchronous rec-
tifier MOSFETs (NL_) and keep the connections for LX_,
PGND_, DH_, and DL_ short and wide. Use multiple
small vias to route these signals from the top to the bot-
tom side. The gate current traces must be short and
wide, measuring 50 mils to 100 mils wide if the low-side
MOSFET is 1in from the controller IC. Connect each
PGND trace from the IC close to the source terminal of
the respective low-side MOSFET.
Route high-speed switching nodes (BST_, LX_, DH_,
and DL_) away from the sensitive analog areas (RT,
COMP_, LIM_, and FB_). Group all SGND-referred and
feedback components close to the IC. Keep the FB_
and compensation network nets as small as possible to
prevent noise pickup.
C
Qg
V
BST
_
=
相關PDF資料
PDF描述
DS232A LINE TRANSCEIVER, PDIP16
DS2404S-001 0 TIMER(S), REAL TIME CLOCK, PDSO16
DS2404B 0 TIMER(S), REAL TIME CLOCK, PDSO16
DS2404 0 TIMER(S), REAL TIME CLOCK, PDIP16
DS2405P SPECIALTY MEMORY CIRCUIT, PDSO6
相關代理商/技術參數
參數描述
DS232AS/T&R 制造商:Maxim Integrated Products 功能描述:IC TXRX DUAL RS-232 5V 16-SOIC
DS232AS/T&R 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
DS232AS+ 功能描述:RS-232接口集成電路 Dual RS-232 Transmitter/Receiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
DS232AS+T&R 制造商:Maxim Integrated Products 功能描述:IC TXRX DUAL RS-232 5V 16-SOIC
DS232AS+T&R 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: