- 您現在的位置：買賣IC網 > PDF目錄93262 > DS2291 (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY TELECOM CIRCUIT, SMA30 PDF資料下載
參數資料
| 型號： | DS2291 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Telecom IC:Other |
| 英文描述： | SPECIALTY TELECOM CIRCUIT, SMA30 |
| 文件頁數： | 4/10頁 |
| 文件大小： | 144K |
| 代理商： | DS2291 |
DS2291
022798 3/10
PIN DESCRIPTION Table 1
PIN
SYMBOL
I/O
DESCRIPTION
1,2
VDD
-
Positive Supply. 5.0 volts.
3
RCLK
O
Receive Clock. Recovered 1.544 MHz clock.
4
5
RPOS
RNEG
O
Receive Bipolar Data. Recovered bipolar data; updated on the
rising edge of RCLK. Bipolar violations are not corrected.
6
LCLK
I
Loopback Clock. Clock for loopback data. Internally pulled low
by 100K ohm.
7
8
LPOS
LNEG
I
Loopback Bipolar Data. Samples on the falling edge of LCLK
if LB is tied high. Internally pulled low by 100K ohm.
9
LB
I
Loopback Enable. Tie high to loopback data from the LPOS
and LNEG inputs to RPOS and RNEG; tie low or leave open to
obtain recovered data out of the ALBO circuitry at RPOS and
RNEG. Internally pulled low by 100K ohm.
14
RCL
O
Receive Carrier Loss. Transitions high when 192 consecutive
zeros have been received at RX+ and RX-; reset on the next
ones occurrence.
15
BPV
O
Receive Bipolar Violation. Transitions high for a full bit period
when a bipolar violation appears at RX+ and RX-. B8ZS code
words are not reported if B8ZS is tied high.
16
LOCK
O
Lock Indication. High state indicates that the recovery circuit is
phase-and frequency-locked to the signal at RX+ and RX-.
17
BL
O
Buffer Limit. Transitions high when the incoming jitter at RX+
and RX- is greater than 120Ulpp.
19
DJA
I
Disable Jitter Attenuation. Tie high to disable the jitter attenu-
ation circuitry; tie low to enable the jitter attenuation circuitry.
Internally pulled low by 100K ohm.
20
B8ZS
I
B8ZS Enable. If tied high, incoming B8ZS code words are de-
coded and replaced with eight zeros. If tied low, B8ZS code
words are not decoded. Internally pulled low by 100K ohm.
21
RST
I
Reset. Active low; a high-low-high transition will recenter the
dejitter buffer. Internally pulled high by 100K ohm.
22, 23
GND
-
Ground. 0.0 volts.
29
30
RX+
RX-
I
O
Receive Analog Input. Connects to T1 line through a 2:1 trans-
former. See Figure 4.
NOTE:
Do not connect any signal to pins 10, 11, 12, 13, 18, 24, 25, 26, 27, or 28.
相關PDF資料 |
PDF描述 |
|---|---|
| DS229EN | LINE TRANSCEIVER, PDSO20 |
| DS232A-N | LINE TRANSCEIVER, PDIP16 |
| DS2401P | SPECIALTY MEMORY CIRCUIT, PDSO6 |
| DS2401Z/T&R | SPECIALTY MEMORY CIRCUIT, PDSO4 |
| DS2401P/T&R | SPECIALTY MEMORY CIRCUIT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2291/87-22291-000 | 功能描述:網絡控制器與處理器 IC T1 Long Loop Stik RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS229E | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| DS229E/T&R | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| DS229E+ | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| DS229E+T&R | 制造商:Maxim Integrated Products 功能描述:IC TXRX TRI 5V RS-232 20-TSSOP |
發布緊急采購，3分鐘左右您將得到回復。