- 您現在的位置：買賣IC網 > PDF目錄93261 > DS21T07E (MAXIM INTEGRATED PRODUCTS INC) 9-LINE 110 ohm SCSI BUS TERMINATOR, PDSO20 PDF資料下載
參數資料
| 型號： | DS21T07E |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Bus Terminator |
| 英文描述： | 9-LINE 110 ohm SCSI BUS TERMINATOR, PDSO20 |
| 封裝： | 0.173 INCH, PLASTIC, TSSOP-20 |
| 文件頁數： | 2/7頁 |
| 文件大小： | 101K |
| 代理商： | DS21T07E |
DS21T07
2 of 7
FUNCTIONAL DESCRIPTION
The DS21T07 consists of a bandgap reference, buffer amplifier, and nine termination resistors (Figure 1).
The bandgap reference circuit produces a precise 2.55V level which is fed to a buffer amplifier. The
buffer produces a 2.85V level and is capable of sourcing at least 24 mA into each of the termination
resistors when the signal line is low (active). When the driver for a given signal line turns off, the
terminator will pull the signal line to 2.85V (quiescent state). To handle actively negated SCSI signals,
the buffer can sink at least 200 mA, and VREF will move less than 60 mV. When all lines settle in the
quiescent state, the regulator will consume about 5 mA. When the DS21T07 is put into power-down
mode by bringing PD low, the power-down circuitry will turn off the transistors on each signal line. This
will isolate the DS21T07 from the signal lines and effectively remove it from the circuit. The power-
down pin ( PD ) has an internal 50K
=pullup resistor. To place the DS21T07 into an active state, the PD
pin should be left open circuited. When installed on disk drives or RAID system components, the
DS21T07 will not affect the SCSI bus during a hot plug operation.
To ensure proper operation, both the TERMPWR1 and TERMPWR2 pins must be connected to the SCSI
bus TERMPWR line and both the VREF1 and VREF2 pins must be tied together externally. Each
DS21T07 requires a 4.7 F capacitor connected between the VREF pins and ground. Figure 2 details a
typical SCSI bus configuration. In an 8-bit wide SCSI bus arrangement, two DS21T07’s would be needed
at each end of the SCSI cable in order to terminate the 18 active signal lines. In a 16-bit wide SCSI bus
arrangement, three DS21T07’s would be needed at each end of the SCSI cable in order to terminate the
27 active signal lines.
DS21T16 BLOCK DIAGRAM Figure 1
相關PDF資料 |
PDF描述 |
|---|---|
| DS21T07S | 9-LINE 110 ohm SCSI BUS TERMINATOR, PDSO16 |
| DS21T09S | 18-LINE 110 ohm SCSI BUS TERMINATOR, PDSO28 |
| DS2223 | 256 X 1 STANDARD SRAM, 1000 ns, PBCY3 |
| DS2223Z | 256 X 1 STANDARD SRAM, 1000 ns, PDSO4 |
| DS2224 | 224 X 1 STANDARD SRAM, 1000 ns, PBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21T07E/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:DALLAS SEMI 功能描述: 制造商:Maxim Integrated Products 功能描述:IC TERMINATOR SCSI 20-TSSOP |
| DS21T07E/T&R/C16 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS21T07E/T&R | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS21T07E/T&R/C03 | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS21T07E/T&R/C16 | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。