參數資料
型號: DS2155LN+
廠商: Maxim Integrated Products
文件頁數: 58/238頁
文件大小: 0K
描述: IC TXRX T1/E1/J1 1-CHIP 100-LQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 90
功能: 單芯片收發器
接口: E1,HDLC,J1,T1
電路數: 1
電源電壓: 3.14 V ~ 3.47 V
電流 - 電源: 75mA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-LQFP(14x14)
包裝: 管件
包括: BERT 發生器和檢測器,CMI 編碼器和解碼器,HDLC 控制器
產品目錄頁面: 1429 (CN2011-ZH PDF)
DS2155
150 of 238
Register Name:
LIC2
Register Description:
Line Interface Control 2
Register Address:
79h
Bit #
7
6
5
4
3
2
1
0
Name
ETS
LIRST
IBPV
TUA1
JAMUX
SCLD
CLDS
Default
0
Bit 0/Custom Line Driver Select (CLDS). Setting this bit to a 1 redefines the operation of the transmit line
driver. When this bit is set to a 1 and LIC1.5 = LIC1.6 = LIC1.7 = 0, the device generates a square wave at the
TTIP and TRING outputs instead of a normal waveform. When this bit is set to a 1 and LIC1.5 = LIC1.6 = LIC1.7
≠ 0, the device forces TTIP and TRING outputs to become open-drain drivers instead of their normal push-pull
operation. This bit should be set to 0 for normal operation of the device.
Bit 1/Short-Circuit Limit Disable (ETS = 1) (SCLD). Controls the 50mA (RMS) current limiter.
0 = enable 50mA current limiter
1 = disable 50mA current limiter
Bit 2/Unused, must be set to 0 for proper operation
Bit 3/Jitter Attenuator Mux (JAMUX). Controls the source for JACLK.
0 = JACLK sourced from MCLK (2.048MHz or 1.544MHz at MCLK)
1 = JACLK sourced from internal PLL (2.048MHz at MCLK)
Bit 4/Transmit Unframed All Ones (TUA1). The polarity of this bit is set such that the device transmits an all-
ones pattern on power-up or device reset. This bit must be set to a 1 to allow the device to transmit data. The
transmission of this data pattern is always timed off of the JACLK.
0 = transmit all ones at TTIP and TRING
1 = transmit data normally
Bit 5/Insert BPV (IBPV). A 0-to-1 transition on this bit causes a single BPV to be inserted into the transmit data
stream. Once this bit has been toggled from a 0 to a 1, the device waits for the next occurrence of three consecutive
1s to insert the BPV. This bit must be cleared and set again for a subsequent error to be inserted.
Bit 6/Line Interface Reset (LIRST). Setting this bit from a 0 to a 1 initiates an internal reset that resets the clock
recovery state machine and recenters the jitter attenuator. Normally this bit is only toggled on power-up. Must be
cleared and set again for a subsequent reset.
Bit 7/E1/T1 Select (ETS)
0 = T1 mode selected
1 = E1 mode selected
相關PDF資料
PDF描述
VE-BV0-IY-F2 CONVERTER MOD DC/DC 5V 50W
DS21372T+ IC TESTER BIT ERROR 3.3V 32-TQFP
DS2172T+ IC TESTER BIT ERROR RATE 32-TQFP
VE-B1Z-IY-F3 CONVERTER MOD DC/DC 2V 20W
CPC1465MTR IC SHDSL/ISDN DC TERM 16-MLP
相關代理商/技術參數
參數描述
DS2155LN+ 功能描述:網絡控制器與處理器 IC T1/E1/J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2155LNB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2155LNB+ 功能描述:網絡控制器與處理器 IC T1/E1/J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2155LNC2+ 功能描述:網絡控制器與處理器 IC T1/E1/J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2156 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:T1/E1/J1 Single-Chip Transceiver