參數資料
型號: DS21554LB
廠商: Maxim Integrated Products
文件頁數: 79/124頁
文件大?。?/td> 0K
描述: IC TXRX E1 1-CHIP 5V 100-LQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
產品變化通告: Product Discontinuation 20/Feb/2012
標準包裝: 90
功能: 單芯片收發器
接口: E1,HDLC,J1,T1
電路數: 1
電源電壓: 4.75 V ~ 5.25 V
電流 - 電源: 75mA
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-LQFP(14x14)
包裝: 托盤
包括: 遠程和 AIS 警報檢測器 / 發生器
DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers
58 of 124
the TSRs before the old data is retransmitted. ITU specifications recommend that the ABCD signaling not
be set to all zeros because they will emulate a CAS multiframe alignment word.
The TS1 register is special because it contains the CAS multiframe alignment word in its upper nibble.
The upper nibble must always be set to 0000 or else the terminal at the far end loses multiframe
synchronization. If the user wishes to transmit a multiframe alarm to the far end, then the TS1.2 bit
should be set to one. If no alarm is to be transmitted, then the TS1.2 bit should be cleared. The three
remaining bits in TS1 are the spare bits. If they are not used, they should be set to one. In CCS signaling
mode, TS1 to TS16 can also be used to insert signaling information. Via the SR2.5 bit, the user will be
informed when the signaling registers need to be loaded with data. The user has 2ms to load the data
before the old data will be retransmitted.
Via the CCR3.6 bit, the user has the option to use the Transmit Channel Blocking Registers (TCBRs) to
determine on a channel by channel basis, which signaling bits are to be inserted via the TSRs (the
corresponding bit in the TCBRs = 1) and which are to be sourced from the TSER or TSIG pin (the
corresponding bit in the TCBRs = 0). See Figure 18-15 for more details.
9.2.
Hardware-Based Signaling
9.2.1.
Receive Side
In the receive side of the hardware-based signaling, there are two operating modes for the signaling
buffer—signaling extraction and signaling reinsertion. Signaling extraction involves pulling the signaling
bits from the receive data stream and buffering them over a four-multiframe buffer and outputting them in
a serial PCM fashion on a channel-by-channel basis at the RSIG output. This mode is always enabled. In
this mode, the receive elastic store may be enabled or disabled. If the receive elastic store is enabled, then
the backplane clock (RSYSCLK) must be 2.048MHz/4.096MHz/8.192MHz. The ABCD signaling bits
are output on RSIG in the lower nibble of each channel. The RSIG data is updated once a multiframe
(2ms) unless a freeze is in effect. See the timing diagrams in Section 18.1 for some examples.
The other hardware-based signaling operating mode called signaling reinsertion can be invoked by setting
the RSRE control bit high (CCR3.3 = 1). In this mode, the user provides a multiframe sync at the RSYNC
pin and the signaling data is realigned at the RSER output according to this applied multiframe boundary.
In this mode, the elastic store must be enabled and the backplane clock must be
2.048MHz/4.096MHz/8.192MHz.
The signaling data in the two-multiframe buffer is frozen in a known good state upon either a loss of
synchronization (OOF event), carrier loss, or frame slip. To allow this freeze action to occur, the RFE
control bit (CCR2.0) should be set high. The user can force a freeze by setting the RFF control bit
(CCR2.1) high. Setting the RFF bit high causes the same freezing action as if a loss of synchronization,
carrier loss, or slip has occurred.
The two-multiframe buffer provides an approximate one-multiframe delay in the signaling bits provided
at the RSIG pin (and at the RSER pin if RSRE = 1 via CCR3.3). When freezing is enabled (RFE = 1), the
signaling data is held in the last known good state until the corrupting error condition subsides. When the
error condition subsides, the signaling data is held in the old state for an additional 3ms to 5ms before
being allowed to be updated with new signaling data.
相關PDF資料
PDF描述
VE-B6R-IY-B1 CONVERTER MOD DC/DC 7.5V 50W
VE-B6M-IY-B1 CONVERTER MOD DC/DC 10V 50W
VE-B6H-IY-B1 CONVERTER MOD DC/DC 52V 50W
VE-B5D-IY-B1 CONVERTER MOD DC/DC 85V 50W
VE-B5B-IY-B1 CONVERTER MOD DC/DC 95V 50W
相關代理商/技術參數
參數描述
DS21554LB+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21554LBN 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21554LBN+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21554LN 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21554LN+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray