- 您現在的位置：買賣IC網 > PDF目錄379182 > DS21372T 3.3V Bit Error Rate Tester BERT PDF資料下載
參數資料
| 型號： | DS21372T |
| 英文描述： | 3.3V Bit Error Rate Tester BERT |
| 中文描述： | 3.3誤碼率測試儀誤碼 |
| 文件頁數： | 6/21頁 |
| 文件大小： | 214K |
| 代理商： | DS21372T |
DS21372
6 of 21
2.
The DS21372 is controlled via a multiplexed bi-directional address/data bus by an external
microcontroller or microprocessor. The DS21372 can operate with either Intel or Motorola bus timing
configurations. If the BTS pin is tied low, Intel timing will be selected; if tied high, Motorola timing will
be selected. All Motorola bus signals are listed in parenthesis (). See the timing diagrams in the A.C.
Electrical Characteristics for more details. The multiplexed bus on the DS21372 saves pins because the
address information and data information share the same signal paths. The addresses are presented to the
pins in the first portion of the bus cycle and data will be transferred on the pins during second portion of
the bus cycle. Addresses must be valid prior to the falling edge of ALE(AS), at which time the DS21372
latches the address from the AD0 to AD7 pins. Valid write data must be present and held stable during
the later portion of the DS or
WR
pulses. In a read cycle, the DS21372 outputs a byte of data during the
latter portion of the DS or
RD
pulses. The read cycle is terminated and the bus returns to a high
impedance state as
RD
transitions high in Intel timing or as DS transitions low in Motorola timing. The
DS21372 can also be easily connected to non-multiplexed buses. RCLK and TCLK are used to update
counters and load transmit and receive pattern registers. At slow clock rates, sufficient time must be
allowed for these port operations.
PARALLEL CONTROL INTERFACE
3.
The Pattern Set Registers (PSR) are loaded each time a new pattern (whether it be pseudorandom or
repetitive) is to be generated. When a pseudorandom pattern is generated, all four PSRs must be loaded
with FF Hex. When a repetitive pattern is to be created, the four PSRs are loaded with the pattern that is
to be repeated. Please see Tables 4 and 5 for some programming examples.
PATTERN SET REGISTERS
PATTERN SET REGISTERS
(MSB) (LSB)
PS31
PS30
PS29
PS28
PS23
PS22
PS21
PS20
PS15
PS14
PS13
PS12
PS7
PS6
PS5
PS4
PS27
PS19
PS11
PS3
PS26
PS18
PS10
PS2
PS25
PS17
PS9
PS1
PS24
PS16
PS8
PS0
PSR3 (addr.=00 Hex)
PSR2 (addr.=01 Hex)
PSR1 (addr.=02 Hex)
PSR0 (addr.=03 Hex)
4.
Length Bits LB4 to LB0 determine the length of the pseudorandom polynomial or programmable
repetitive pattern that is generated and detected. With the pseudorandom patterns, the “Tap A” feedback
position of the pattern generator is always equal to the value in the Pattern Length Register (PLR). Please
refer to Figure 2 for a block diagram of the pattern generator and to Tables 4 and 5 for some
programming examples.
PATTERN LENGTH REGISTER
相關PDF資料 |
PDF描述 |
|---|---|
| DS21372TN | 3.3V Bit Error Rate Tester BERT |
| DS2141A | T1 Controller |
| DS2143 | E1/ISDN-PRI framing transceiver |
| DS2143Q | E1/ISDN-PRI framing transceiver |
| DS21455 | Quad T1/E1/J1 Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21372T+ | 功能描述:網絡控制器與處理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21372TN | 功能描述:網絡控制器與處理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21372TN+ | 功能描述:網絡控制器與處理器 IC 3.3V Bit Error Rate Tester (BERT) RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS214 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DS2141A | 功能描述:網絡控制器與處理器 IC T1 Controller w/Elastic Store RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。