- 您現在的位置：買賣IC網 > PDF目錄358701 > DS2132AN Solid-State Recorder PDF資料下載
參數資料
| 型號： | DS2132AN |
| 英文描述： | Solid-State Recorder |
| 中文描述： | 固態記錄儀 |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 501K |
| 代理商： | DS2132AN |
DS2149DK/DS21349DK T1/J1 Line Interface Unit Design Kit
6 of 14
BASIC CONFIGURATION
The following example configurations provide a quick start to using the DS2149DK/DS21349DK, although there are
many ways they can be configured. To set up other configurations, refer to the DS2149/DS21349 data sheets in
addition to this data sheet.
T1 Hardware Mode—External Remote Loopback
1) On the system connector, jumper TPOS to RPOS, TNEG to RNEG, RCLK_CON to TCLK, and
RELAY_CONTROL to GND.
2) JP8, jumper RCLK to CON.
3) Remove JP5, TCLK_EN.
4) Jumper JP6 MCLK_EN.
5) JP9, JASEL, jumper to GND.
6) JP7, TAIS, jumper to GND.
7) JP10, MODE0, jumper to GND.
8) Jumper JP3, MODE1_EN.
9) Jumper JP4, RLS_EN.
10) Jumper JP2, LLB_EN.
11) On SW1, switch MODE1 to MODE1_LO.
12) On SW1, switch L0 to L0_HI.
13) On SW1, switch L1 to L1_HI.
14) On SW1, switch L2 to L2_LO.
15) On SW1, switch L3 to L3_LO.
16) On SW1, switch RLB to RLB_LO.
17) On SW1, switch LLB to LLB_LO.
18) Place appropriate device in socket.
19) Select the power 5V or 3V depending on which device you use.
20) Connect J2 and J3 to test equipment
Device should be in external remote loopback.
T1 Software Mode—External Remote Loopback
1) On the system connector, jumper TPOS to RPOS, TNEG to RNEG, RCLK_CON to TCLK, and
RELAY_CONTROL to GND.
2) JP8, jumper RCLK to CON.
3) Remove JP5, TCLK_EN.
4) Jumper JP6 MCLK_EN.
5) JP9, JASEL, jumper to GND.
6) JP7, TAIS, jumper to GND.
7) JP10, MODE0, jumper to GND.
8) Jumper JP3, MODE1_EN.
9) Jumper JP4, RLS_EN.
10) Jumper JP2, LLB_EN.
11) On SW1, switch MODE1 to MODE1_HI.
12) Place appropriate device in socket.
13) Select the power 5V or 3V depending on which device you use.
14) Connect J2 and J3 to test equipment.
15) Load the DemoView software.
16) Select RegView.
17) Load the DS2149.DEF file.
18) Write CR1 to 0x03.
19) Write CR2 to 0x00.
20) Write CR3 to 0x00.
21) Write CR4 to 0x00.
Device should be in external remote loopback.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2132A | Solid-State Recorder |
| DS2130QN | Solid-State Recorder |
| DS2130Q | Solid-State Recorder |
| DS2130N | Solid-State Recorder |
| DS2130 | Solid-State Recorder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2132AQ | 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DS2132AQN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| DS21348 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3.3V E1/T1/J1 Line Interface |
| DS21348DK | 功能描述:網絡開發工具 DS21348 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS21348G | 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。