- 您現在的位置：買賣IC網 > PDF目錄385272 > DS1881Z-045R (Maxim Integrated Products, Inc.) Dual NV Audio Taper Digital Potentiometer PDF資料下載
參數資料
| 型號： | DS1881Z-045R |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 數字電位計 |
| 英文描述： | Dual NV Audio Taper Digital Potentiometer |
| 中文描述： | 錐形雙非易失數字電位器音頻 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 234K |
| 代理商： | DS1881Z-045R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
D
Dual NV Audio Taper Digital Potentiometer
14
____________________________________________________________________
setup time (see Figure 4) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master gener-
ates all SCL clock pulses including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK):
An Acknowledge-
ment (ACK) or Not Acknowledge (NACK) is always the
9th bit transmitted during a byte transfer. The device
receiving data (the master during a read or the slave
during a write operation) performs an ACK by transmit-
ting a zero during the 9th bit. A device performs a
NACK by transmitting a one during the 9th bit. Timing
(Figure 4) for the ACK and NACK is identical to all other
bit writes. An ACK is the acknowledgment that the
device is properly receiving data. A NACK is used to
terminate a read sequence or as an indication that the
device is not receiving data.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
1
2
6
7
8
9
1
2
8
9
3–7
Figure 3. Data Transfer Protocol
SDA
SCL
t
HD:STA
t
LOW
t
HIGH
t
R
t
F
t
HD:DAT
t
SU:DAT
REPEATED
START
t
SU:STA
t
HD:STA
t
SU:STO
t
SP
STOP
START
t
BUF
NOTE: TIMING IS REFERENCED TO V
IL(MAX)
AND V
IH(MIN)
.
Figure 4. I
2
C Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| DS1881Z-045T | Dual NV Audio Taper Digital Potentiometer |
| DS1882 | Dual Log Audio Digital Potentiometer |
| DS18S20 | High Precision 1-Wire Digital Thermometer(高精度1線數字溫度計) |
| DS1920 | Temperature Button(溫度按鈕) |
| DS1962 | 1K-Bit Monetary iButton(1K位貨幣按鈕) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1881Z-045T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual NV Audio Taper Digital Potentiometer |
| DS1881Z-050 | 制造商:Maxim Integrated Products 功能描述:DUAL NV 45K AUDIO POT SOIC 16 - Rail/Tube |
| DS1881Z-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV 45K AUDIO POT SOIC-16 TRL - Tape and Reel |
| DS1881Z-050+ | 功能描述:數字電位計 IC Dual NV Audio Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1881Z-050+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 64POS 45KOHM DUAL 16SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DGTL POT NV 2CH 45K 16-SOIC |
發布緊急采購，3分鐘左右您將得到回復。