- 您現在的位置：買賣IC網 > PDF目錄379181 > DS1866Z Log Trimmer Potentiometer PDF資料下載
參數資料
| 型號： | DS1866Z |
| 元件分類： | 數字電位計 |
| 英文描述： | Log Trimmer Potentiometer |
| 中文描述： | 日志電位器 |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 77K |
| 代理商： | DS1866Z |
DS1866
5 of 5
102199
NOTES:
1.
All voltages are referenced to ground.
2.
For V
CC
= 5V ± 10% maximum V
IL
= +0.8V. For V
CC
3.0 ± 10% V
IL
= +0.6V. For V
CC
=2.7 volts V
IH
=2.0 volts minimum.
3.
Resistor input voltages cannot go below ground or exceed V
CC
by the amounts as shown in the table.
4.
Maximum current specifications are based on the change rate of the parallel port inputs P0, P1, and
P2.
5.
Standby current specifications apply when P0, P1, P2 logic inputs are driven within the specified V
IH
or V
IL
levels.
6.
Valid at 25
°
C only.
7.
The end-to-end resistance tolerance of the DS1866 can be expected to shift with temperature.
However, this change will not exceed ±20% of the nominal resistor value of the part.
8.
Absolute tolerance is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position. The DS1866 is specified to provide an absolute tolerance of ±1.0 dB.
9.
Tap-to-tap tolerance is used to determine the change in voltage between successive tap positions. The
DS1866 is specified to provide a tap-to-tap tolerance specification of ±1.0 dB.
10.
-3 dB cutoff frequency characteristic for the DS1866 is 1 MHz.
11.
Capacitance values apply at 25°C.
12.
This specification refers to the time difference between parallel port input changes to stabilize a wiper
transition.
DS1866 ORDERING INFORMATION
ORDERING NUMBER
PACKAGE
OPERATING
TEMPERATURE
-40°C TO +85°C
-40°C TO +85°C
VERSION
DS1866
DS1866Z
8L DIP
8L SOIC (150-MIL)
10k
10k
相關PDF資料 |
PDF描述 |
|---|---|
| DS18B20Z | Programmable Resolution 1-Wire Digital Thermometer |
| DS18S20Z | High Precision 1-Wire Digital Thermometer |
| DS1923 | Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory |
| DS1923-F5 | Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory |
| DS1990 | Serial Number iButton |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1866Z/T&R | 制造商:Maxim Integrated Products 功能描述:DIG LOG TRIM POT 10KOHM 8L 150ML TR - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT TRIM LOG 2.7-5.5V 8-SOIC |
| DS1866Z/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1866Z+ | 功能描述:數字電位計 IC Log Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1866Z+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 8POS 10KOHM SGL 8SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT TRIM LOG 2.7-5.5V 8-SOIC 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs Log Trimmer |
| DS1866Z+T&R | 功能描述:數字電位計 IC Log Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。