- 您現在的位置：買賣IC網 > PDF目錄379181 > DS1866 Log Trimmer Potentiometer PDF資料下載
參數資料
| 型號： | DS1866 |
| 元件分類： | 數字電位計 |
| 英文描述： | Log Trimmer Potentiometer |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 77K |
| 代理商： | DS1866 |
DS1866
2 of 5
102199
OPERATION
The DS1866 is a single volatile potentiometer. The device has a total of eight positions providing a
resolution of 5 dB per step and giving a total attenuation range of 0 dB to -35 dB. These tap points are
accessible to the W-terminal whose position is controlled via a 3-terminal parallel port consisting of input
signals P0, P1, and P2. A block diagram of the DS1866 is shown in Figure 1.
Wiper position setting of the DS1866 is determined by the states of the P0, P1, and P2 input terminals.
Table 1 below outlines position setting versus value of the parallel port inputs. A Position-0 setting places
the wiper position at the L-terminal of the potentiometer and provides 35 dB of attenuation. As wiper
position increases, attenuation decreases with Position-7 giving 0 dB of attenuation.
On power-up, the wiper position of the DS1866 will be set to the P0, P1, and P2 values.
P2 P1 P0
(binary)
000
001
010
011
100
101
110
111
Wiper
Position
0
1
2
3
4
5
6
7
Attenuation
(dB)
35 dB
30 dB
25 dB
20 dB
15 dB
10 dB
5 dB
0 dB
PIN DESCRIPTIONS
V
CC
- Power Supply Terminal.
The DS1866 will support supply voltages ranging from +2.7 to +5.5
volts.
GND - Ground Terminal.
H - High-end Resistor.
This is the high-end terminal of the potentiometer. It is not required that this
terminal be connected to a potential greater than the L-terminal. Maximum voltage on the H-terminal can
not exceed the power supply voltage, V
CC
, or go below ground.
L - Low-end Resistor.
This is the low-end terminal of the potentiometer. It is not required that this
terminal be connected to a potential less than the H-terminal. Maximum voltage on the L-terminal can not
exceed the power-supply voltage, V
CC
, or go below ground.
W - Wiper of the Potentiometer.
This pin is the wiper terminal of the potentiometer. Its position on the
resistor array is controlled by the 3-terminal parallel port. Maximum voltage on the W-terminal can not
exceed the power supply voltage, V
CC
, or go below ground.
P0 - Bit 0.
P0 is the bit 0 data input to the parallel port.
P1 - Bit 1.
P1 is the bit 1 data input to the parallel port.
P2 - Bit 2.
P2 is the bit 2 data input to the parallel port.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1866Z | Log Trimmer Potentiometer |
| DS18B20Z | Programmable Resolution 1-Wire Digital Thermometer |
| DS18S20Z | High Precision 1-Wire Digital Thermometer |
| DS1923 | Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory |
| DS1923-F5 | Hygrochron Temperature/Humidity Logger iButton with 8kB Data Log Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1866+ | 功能描述:數字電位計 IC Log Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1866N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1866S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1866SN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1866Z | 功能描述:數字電位計 IC Log Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。