- 您現在的位置：買賣IC網 > PDF目錄8537 > DS1851E-010+T&R (Maxim Integrated Products)IC DAC DUAL NV TEMP CNTRL 8TSSOP PDF資料下載
參數資料
| 型號： | DS1851E-010+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC DUAL NV TEMP CNTRL 8TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 8 |
| 數據接口： | 串行 |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 95°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 8-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 2 電壓，單極 |
| 采樣率（每秒）： | * |
DS1851
8 of 18
2-WIRE OPERATION
Clock and Data Transitions
The SDA pin is normally pulled high with an external resistor or device. Data on the SDA pin may only
change during SCL low time periods. Data changes during SCL high periods will indicate a START or
STOP conditions depending on the conditions discussed below. Refer to the Timing Diagram in Figure 4
for further details.
START Condition
A high-to-low transition of SDA with SCL high is a START condition that must precede any other
command. Refer to the timing diagram in Figure 4 for further details.
STOP Condition
A low-to-high transition of SDA with SCL high is a STOP condition. After a read sequence, the stop
command places the DS1851 into a low-power mode. Refer to the timing diagram in Figure 4 for further
details.
Acknowledge Bit
All address bytes and data bytes are transmitted via a serial protocol. The DS1851 pulls SDA low during
the ninth clock pulse to acknowledge that it has received each word.
Standby Mode
The DS1851 features a low-power mode that is automatically enabled after power-on, after a STOP
command, and after the completion of all internal operations.
2-Wire Interface Reset
After any interruption in protocol, power loss, or system reset, the following steps reset the DS1851:
1) Clock up to nine cycles.
2) Look for SDA high in each cycle while SCL is high.
3) Create a START condition while SDA is high.
Device Addressing
The DS1851 must receive an 8-bit device address word following a START condition to enable a specific
device for a read or write operation. The address word is clocked into the DS1851 MSB to LSB. The
address word consists of Ah (1010) followed by 000 then the R/W bit. If the R/W bit is high, a read
operation is initiated. The R/W is low, a write operation is initiated. Upon a match of the address, the
DS1851 will output a zero for one clock cycle as an acknowledge. If the address does not match, the
DS1851 ignores the communication.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1187CS8#TRPBF | IC AMP VIDEO DIFFRNC ADJ 8-SOIC |
| VI-B33-MU-F3 | CONVERTER MOD DC/DC 24V 200W |
| MAX5521ETC+T | IC DAC 10BIT SGL ULP 12-TQFN |
| VI-B5N-MX-S | CONVERTER MOD DC/DC 18.5V 75W |
| VI-B33-MU-F2 | CONVERTER MOD DC/DC 24V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1852 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Optical Transceiver Diagnostic Monitor |
| DS1852B-000 | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1852B-000/C | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS1852B-000/T&R | 制造商:Maxim Integrated Products 功能描述:IC MONITOR TXRX OPTICAL 25-BGA |
| DS1852B-000/T&R | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。