- 您現在的位置：買賣IC網 > PDF目錄379181 > DS1847-010 Dual Temperature-Controlled NV Variable Resistor PDF資料下載
參數資料
| 型號： | DS1847-010 |
| 英文描述： | Dual Temperature-Controlled NV Variable Resistor |
| 中文描述： | 雙溫控非易失可變電阻 |
| 文件頁數： | 4/17頁 |
| 文件大小： | 239K |
| 代理商： | DS1847-010 |
DS1847
4 of 17
Memory
Location
00h to 47h
Name of Location
Function of Location
(Table Select
Byte, E0h, must
be set to 01h or
02h to access the
Look-Up Tables)
User Defined Look-Up Table
(LUT)
This block contains the user defined temperature
settings of the resistors. Values between 00h and
FFh can be written to either table to set the 256
position variable resistors. The first address
location, 00h, is used to set the resistor at -40°C.
Each successive memory location will contain the
resistor setting for the previous temperature +2°C.
For example, memory address 01h is the address
that will set the resistor in a –38°C environment.
For default memory settings and programming
the look-up table, refer to the Programming the
Look-Up Table (LUT) section of the datasheet.
Writing to this byte determines which of the two
72x8 EEPROM look-up tables is selected for
reading or writing.
01h (Look-Up Table 1 selected)
02h (Look-Up Table 2 selected)
E0h
Table Select Byte
E1h
Configuration Byte
TAU – Temperature/Address Update
TEN – Temperature Update Enable
AEN – Address Update Enable
Default setting is 03h, TAU = 1, TEN = 1 and
AEN = 1.
TAU becomes a 1 after a temperature and address
update has occurred as a result of a temperature
conversion. The user can write this bit to 0 and
check for a transition from 0 to 1 in order to
verify that a conversion has occurred.
If TEN = 0, the temperature conversion feature is
disabled. The user sets the resistor in “manual
mode” by writing to addresses F0h and
F1h to control resistors 0 and 1, respectively.
With AEN = 0 the user can operate in a test
mode. Address updates made from the
temperature sensor will cease. The user can load a
memory location into E4h and verify that the
values in locations F0h and F1h are the expected
user-defined values.
TAU TEN AEN
相關PDF資料 |
PDF描述 |
|---|---|
| DS1847-050 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847B-010 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847B-050 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847E-010 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847E-050 | Dual Temperature-Controlled NV Variable Resistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1847-050 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Temperature-Controlled NV Variable Resistor |
| DS1847B-010 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1847B-010/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV TEMP CNTRL VAR RES 10/10K T - Tape and Reel |
| DS1847B-010/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1847B-010+ | 功能描述:數字電位計 IC Dual Temp Controlled NV Variable Resistor RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。