- 您現在的位置：買賣IC網 > PDF目錄9179 > DS1845E-100+T&R (Maxim Integrated Products)IC POT/MEM DUAL NV 100K 14-TSSOP PDF資料下載
參數資料
| 型號： | DS1845E-100+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT/MEM DUAL NV 100K 14-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 100，256 |
| 電阻（歐姆）： | 10k，100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
DS1845
4 of 14
2-Wire Interface Reset: After any interruption in protocol, power loss, or system reset, the following
steps reset the DS1845.
1. Clock up to nine cycles.
2. Look for SDA high in each cycle while SCL is high.
3. Create a start condition while SDA is high.
Device Addressing: The DS1845 must receive an 8-bit device address word following a start condition
to enable a specific device for a read or write operation. The address word is clocked into the DS1845
MSB to LSB. The address word consists of Ah (1010) followed by A2, A1, and A0 then the R/W
(READ/WRITE) bit. If the R/W bit is high, a read operation is initiated. The R/W is low, a write
operation is initiated. For a device to become active, the values of A2, A1 and A0 must be the same as
the hard-wired address pins on the DS1845. Upon a match of written and hard-wired addresses, the
DS1845 will output a zero for one clock cycle as an acknowledge. If the address does not match the
DS1845 returns to a low-power mode.
Write Operations: After receiving a matching address byte with the R/W bit set low, the device goes
into the write mode of operation. The master must transmit an 8-bit EEPROM memory address to the
device to define the address where the data is to be written. After the reception of this byte, the DS1845
will transmit a zero for one clock cycle to acknowledge the receipt of the address. The master must then
transmit an 8-bit data word to be written into this address. The DS1845 will again transmit a zero for one
clock cycle to acknowledge the receipt of the data. At this point the master must terminate the write
operation with a stop condition. The DS1845 then enters an internally timed write process tw to the
EEPROM memory. All inputs are disabled during this byte write cycle.
The DS1845 is capable of an 8-byte page write. A page write is initiated the same way as a byte write,
but the master does not send a stop condition after the 1st byte. Instead, after the slave acknowledges
receipt of the data byte, the master can send up to seven more bytes using the same nine-clock sequence.
The master must terminate the write cycle with a stop condition or the data clocked into the DS1845 will
not be latched into permanent memory.
Acknowledge Polling: Once the internally-timed write has started and the DS1845 inputs are disabled,
acknowledge polling can be initiated. The process involves transmitting a start condition followed by the
device address. The R/W bit signifies the type of operation that is desired. The read or write sequence
will only be allowed to proceed if the internal write cycle has completed and the DS1845 responds with a
zero.
Read Operations: After receiving a matching address byte with the R/W bit set high, the device goes
into the read mode of operation. There are three read operations: current address read, random read and
sequential address read.
相關PDF資料 |
PDF描述 |
|---|---|
| P3P25814AG-08SR | IC CLOCK GEN 16-128MHZ 8-SOIC |
| 7SB3126BMX1TCG | 1 BIT BUS SWITCH 6UDFN |
| DS1855E-050+T&R | IC RES TEMP-CNTRL 10/50K 14TSSOP |
| DS1855E-010+T&R | IC RES TEMP-CNTRL 10/10K 14TSSOP |
| 7SB3257MUTCG | 1 BIT MUX/DEMUX BUS SWTCH UDFN6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1845E-50+T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT & MEM LEAD FREE - Tape and Reel |
| DS1845X-010 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual NV Potentiometer and Memory |
| DS1845X-010/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT AND MEM BUMP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT/MEM DUAL NV 10K 14-FCP |
| DS1845X-010/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1845X-050 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual NV Potentiometer and Memory |
發布緊急采購，3分鐘左右您將得到回復。