- 您現在的位置：買賣IC網 > PDF目錄385272 > DS1825 (Maxim Integrated Products, Inc.) Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID PDF資料下載
參數資料
| 型號： | DS1825 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| 中文描述： | 分辨率可編程設置的1-Wire數字溫度計，帶有4位ID |
| 文件頁數： | 9/21頁 |
| 文件大?。?/td> | 298K |
| 代理商： | DS1825 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
DS1825 Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID
Table 4. THERMOMETER RESOLUTION CONFIGURATION
9 of 21
R1
0
0
1
1
R0
0
1
0
1
Resolution
9-bit
10-bit
11-bit
12-bit
Max Conversion Time
93.75ms
187.5ms
375ms
750ms
(t
CONV
/8)
(t
CONV
/4)
(t
CONV
/2)
(t
CONV
)
CRC GENERATION
CRC bytes are provided as part of the DS1825’s 64-bit ROM code and in the 9
th
byte of the scratchpad memory.
The ROM code CRC is calculated from the first 56 bits of the ROM code and is contained in the most significant
byte of the ROM. The scratchpad CRC is calculated from the data stored in the scratchpad, and therefore it
changes when the data in the scratchpad changes. The CRCs provide the bus master with a method of data
validation when data is read from the DS1825. To verify that data has been read correctly, the bus master must re-
calculate the CRC from the received data and then compare this value to either the ROM code CRC (for ROM
reads) or to the scratchpad CRC (for scratchpad reads). If the calculated CRC matches the read CRC, the data has
been received error free. The comparison of CRC values and the decision to continue with an operation are
determined entirely by the bus master. There is no circuitry inside the DS1825 that prevents a command sequence
from proceeding if the DS1825 CRC (ROM or scratchpad) does not match the value generated by the bus master.
The equivalent polynomial function of the CRC (ROM or scratchpad) is:
CRC = X
8
+ X
5
+ X
4
+ 1
The bus master can re-calculate the CRC and compare it to the CRC values from the DS1825 using the polynomial
generator shown in Figure 9. This circuit consists of a shift register and XOR gates, and the shift register bits are
initialized to 0. Starting with the least significant bit of the ROM code or the least significant bit of byte 0 in the
scratchpad, one bit at a time should shifted into the shift register. After shifting in the 56
bit from the ROM or the
most significant bit of byte 7 from the scratchpad, the polynomial generator will contain the re-calculated CRC.
Next, the 8-bit ROM code or scratchpad CRC from the DS1825 must be shifted into the circuit. At this point, if the
re-calculated CRC was correct, the shift register will contain all 0s. Additional information about the Dallas 1-Wire
cyclic redundancy check is available in Application Note 27 entitled “Understanding and Using Cyclic Redundancy
Checks with Dallas Semiconductor Touch Memory Products.”
Figure 9. CRC GENERATOR
1-Wire BUS SYSTEM
The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS1825 is always a
slave. When there is only one slave on the bus, the system is referred to as a “single-drop” system; the system is
“multidrop” if there are multiple slaves on the bus.
All data and commands are transmitted least significant bit first over the 1-Wire bus.
The following discussion of the 1-Wire bus system is broken down into three topics: hardware configuration,
transaction sequence, and 1-Wire signaling (signal types and timing).
(MSB)
(LSB)
XOR
XOR
XOR
INPUT
相關PDF資料 |
PDF描述 |
|---|---|
| DS1825U | Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| DS1825UTR | Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| DS1830 | Programmable MicroMonitor(可編程微監控器) |
| DS1832 | 3.3 Volt MicroMonitor Chip(3.3 V微監控芯片) |
| DS1833 | 5V EconoReset(5V Econo監控芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1825U | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1825U/T&R | 制造商:Maxim Integrated Products 功能描述:1-W PROGRAMMABLE DGT THERM 8P USOP - Tape and Reel |
| DS1825U/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1825U/TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Programmable Resolution 1-Wire Digital Thermometer With 4-Bit ID |
| DS1825U+ | 功能描述:板上安裝溫度傳感器 Prog Resolution 1-Wire w/4-Bit ID RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。