參數資料
型號： DS17485SN-5+
廠商： Maxim Integrated Products
文件頁數： 17/31頁
文件大?。?/td> 0K
描述： IC RTC 5V 4K NV RAM 24-SOIC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 31
類型： 時鐘/日歷
特點： 警報器，夏令時，閏年，NVSRAM，方波輸出
存儲容量： 4KB
時間格式： HH:MM:SS（12/24 小時）
數據格式： YY-MM-DD-dd
接口： 并聯
電源電壓： 4.5 V ~ 5.5 V
電壓 - 電源，電池： 2.5 V ~ 3.7 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 24-SOIC W
包裝： 管件
DS17285/DS17287/DS17485/DS17487/DS17885/DS17887
At the beginning of interval 3, the system processor has
begun code execution and clears the interrupt condi-
tion of WF and/or KF by writing zeros to both of these
control bits. As long as no other interrupt within the
DS17x85/DS17x87 is pending, the IRQ line is taken
inactive once these bits are reset. Execution of the
application software can proceed. During this time, the
wake-up and kickstart functions can be used to gener-
ate status and interrupts. WF is set in response to a
date, hours, minutes, and seconds match condition. KF
is set in response to a low-going transition on KS. If the
associated interrupt-enable bit is set (WIE and/or KSE),
the IRQ line is driven active low in response to enabled
event. In addition, the other possible interrupt sources
within the DS17885/DS17887 can cause IRQ to be dri-
ven low. While system power is applied, the on-chip
logic always attempts to drive the PWR pin active in
response to the enabled kickstart or wake-up condition.
This is true even if PWR was previously inactive as the
result of power being applied by some means other
than wake-up or kickstart.
The system can be powered down under software con-
trol by setting the PAB bit to logic 1. This causes the
open-drain PWR pin to be placed in a high-impedance
state, as shown at the beginning of interval 4 in the tim-
ing diagram. As VCC voltage decays, the IRQ output
pin is placed in a high-impedance state when VCC
goes below VPF. If the system is to be again powered
on in response to a wake-up or kickstart, then the WF
and KF flags should be cleared, and WIE and/or KSE
should be enabled prior to setting the PAB bit.
During interval 5, the system is fully powered down.
Battery backup of the clock calendar and NV RAM is in
effect and IRQ is tri-stated, and monitoring of wake-up
and kickstart takes place. If PRS = 1, PWR stays active;
otherwise, if PRS = 0, PWR is high impedance.
RAM Clear
The DS17x85/DS17x87 provide a RAM clear function
for the 114 bytes of user RAM. When enabled, this
function can be performed regardless of the condition
of the VCC pin.
The RAM clear function is enabled or disabled through
the RAM clear-enable bit (RCE; bank 1, register 04BH).
When this bit is set to logic 1, the 114 bytes of user RAM
is cleared (all bits set to 1) when an active-low transition
is sensed on the RCLR pin. This action has no effect on
either the clock/calendar settings or the contents of the
extended RAM. The RAM clear flag (RF, bank 1, register
04AH) is set when the RAM clear operation has been
completed. If VCC is present at the time of the RAM
clear and RIE = 1, the IRQ line is also driven low upon
completion. Writing a zero to the RF bit clears the inter-
rupt condition. The IRQ line then returns to its inactive
high level, provided there are no other pending inter-
rupts. Once the RCLR pin is activated, all read/write
accesses are locked out for a minimum recover time,
specified as tREC in Electrical Characteristics.
When RCE is cleared to 0, the RAM clear function is
disabled. The state of the RCLR pin has no effect on
the contents of the user RAM, and transitions on the
RCLR pin have no effect on RF.
Extended RAM
The DS17x85/DS17x87 provide 2k, 4k, or 8k x 8 of on-
chip SRAM that is controlled as nonvolatile storage sus-
tained from a lithium battery. On power-up, the RAM is
taken out of write-protect status by the internal power-
OK signal (POK) generated from the write-protect cir-
cuitry. The on-chip SRAM is accessed through the
eight multiplexed address/data lines AD7 to AD0. Three
on-chip latch registers control access to the SRAM.
Two registers are used to hold the SRAM address, and
the other register is used to hold read/write data.
Access to the extended RAM is controlled by three of
the registers shown in Table 5. The extended registers
in bank 1 must first be selected by setting the DV0 bit
in register A to logic 1. The address of the RAM loca-
tion to be accessed must be loaded into the extended
RAM address registers located at 50h and 51h. The
least significant address byte should be written to loca-
tion 50h, and the most significant bits (right-justified)
should be loaded in location 51h. Data in the
addressed location can be read by performing a read
operation from location 53h, or written to by performing
a write operation to location 53h. Data in any
addressed location can be read or written repeatedly
without changing the address in location 50h and 51h.
To read or write consecutive extended RAM locations,
a burst mode feature can be enabled to increment the
extended RAM address. To enable the burst mode fea-
ture, set the BME bit in the Extended Control Register
4Ah to logic 1. With burst mode enabled, write the
extended RAM starting address location to registers
50h and 51h. Then read or write the extended RAM
data from/to register 53h. The extended RAM address
locations are automatically incremented on the rising
edge of RD or WR only when register 53h is being
accessed. See the
Burst Mode Timing Waveform.
Real-Time Clocks
24
____________________________________________________________________
相關PDF資料
PDF描述
DS12885QN+ IC RTC W/RAM 128 BYTE IND 28PLCC
MCP4131T-103E/SN IC POT DGTL SNGL 10K SPI 8SOIC
DS12885SN+ IC RTC W/RAM 128 BYTE IND 24SOIC
VI-B5D-IU-S CONVERTER MOD DC/DC 85V 200W
DS17485S-5+ IC RTC 5V 4K NV RAM 24-SOIC
相關代理商/技術參數
參數描述
DS17485SN-5/T&R 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS17485SN-5+ 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS17486 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock
DS17487 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock
DS17487-3 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*