- 您現在的位置：買賣IC網 > PDF目錄9351 > DS1743-85+ (Maxim Integrated Products)IC RTC RAM Y2K 5V 85NS 28-EDIP PDF資料下載
參數資料
| 型號： | DS1743-85+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC RAM Y2K 5V 85NS 28-EDIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 12 |
| 類型： | 時鐘/日歷 |
| 特點： | 閏年，NVSRAM，Y2K |
| 存儲容量： | 8KB |
| 時間格式： | HH:MM:SS（24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 并聯 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP 模塊（0.600"，15.24mm） |
| 供應商設備封裝： | 28-EDIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1434 (CN2011-ZH PDF) |
DS1743/DS1743P Y2K-Compliant, Nonvolatile Timekeeping RAMs
8 of 17
WRITING DATA TO RAM OR CLOCK
The DS1743 is in the write mode whenever WE, and CE are in their active state. The start of a write is
referenced to the latter occurring transition of WE, on CE. The addresses must be held valid throughout the
cycle. CE or WE must return inactive for a minimum of tWR prior to the initiation of another read or write
cycle. Data in must be valid tDS prior to the end of write and remain valid for tDH afterward. In a typical
application, the OE signal will be high during a write cycle. However, OE can be active provided that care
is taken with the data bus to avoid bus contention. If OE is low prior to WE transitioning low the data bus
can become active with read data defined by the address inputs. A low transition on WE will then disable
the outputs tWEZ after WE goes active.
DATA-RETENTION MODE
The 5V device is fully accessible and data can be written or read only when VCC is greater than VPF.
However, when VCC is below the power-fail point, VPF, (point at which write protection occurs) the
internal clock registers and SRAM are blocked from any access. At this time (PowerCap only) the power-
fail reset-output signal (RST) is driven active and remains active until VCC returns to nominal levels. When
VCC falls below the battery switch point VSO (battery supply level), device power is switched from the VCC
in to the backup battery. RTC operation and SRAM data are maintained from the battery until VCC is
returned to nominal levels.
The 3.3V device is fully accessible and data can be written or read only when VCC is greater than VPF.
When VCC falls below the power-fail point, VPF, access to the device is inhibited. At this time the power-
fail reset-output signal (RST) is driven active and remains active until VCC returns to nominal levels. If VPF
is less than VSO, the device power is switched from VCC to the backup supply (VBAT) when VCC drops
below VPF. If VPF is greater than VSO, the device power is switched from VCC to the backup supply (VBAT)
when VCC drops below VSO. RTC operation and SRAM data are maintained from the battery until VCC is
returned to nominal levels. The RST (PowerCap only) signal is an open-drain output and requires a pullup
resistor. Except for RST, all control, data, and address signals must be powered down when VCC is
powered down.
BATTERY LONGEVITY
The DS1743 has a lithium power source that is designed to provide energy for clock activity and clock and
RAM data retention when the VCC supply is not present. The capability of this internal power supply is
sufficient to power the DS1743 continuously for the life of the equipment in which it is installed. For
specification purposes, the life expectancy is 10 years at +25°C with the internal clock oscillator running in
the absence of VCC power. Each DS1743 is shipped from Dallas Semiconductor with its lithium energy
source disconnected, guaranteeing full energy capacity. When VCC is first applied at a level greater than
VPF, the lithium energy source is enabled for battery backup operation. Actual life expectancy of the
DS1743 will be longer than 10 years since no lithium battery energy is consumed when VCC is present.
BATTERY MONITOR
The DS1743 constantly monitors the battery voltage of the internal battery. The battery flag bit (bit 7) of
the day register is used to indicate the voltage level range of the battery. This bit is not writeable and
should always be a 1 when read. If a 0 is ever present, an exhausted lithium energy source is indicated and
both the contents of the RTC and RAM are questionable.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B5F-MW-B1 | CONVERTER MOD DC/DC 72V 100W |
| VE-25F-MW | CONVERTER MOD DC/DC 72V 100W |
| DS1501YE+ | IC RTC WDOG Y2K 5V 28-TSOP |
| VI-BNZ-MY-F2 | CONVERTER MOD DC/DC 2V 20W |
| VE-B5B-MV | CONVERTER MOD DC/DC 95V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1743-85+ | 功能描述:實時時鐘 Timekeeping NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1743-85IND+ | 功能描述:實時時鐘 Timekeeping NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1743P | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Y2K-Compliant, Nonvolatile Timekeeping |
| DS1743P/WP | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PowerCap with Crystal |
| DS1743P-100 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。