- 您現在的位置：買賣IC網 > PDF目錄9363 > DS1685E-3 (Maxim Integrated Products)IC RTC 3V 64-BIT Y2KC 24-TSSOP PDF資料下載
參數資料
| 型號： | DS1685E-3 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 29/34頁 |
| 文件大小： | 0K |
| 描述： | IC RTC 3V 64-BIT Y2KC 24-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 62 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，NVSRAM，方波輸出，Y2K |
| 存儲容量： | 242B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 并聯 |
| 電源電壓： | 2.7 V ~ 3.7 V |
| 電壓 - 電源，電池： | 2.5 V ~ 3.7 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
| 其它名稱： | DS1685E3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁
DS1685/DS1687 3V/5V Real-Time Clocks
4 of 34
PIN DESCRIPTIONS
PIN
NAME
FUNCTION
DS1685
DS1687
PDIP,
SO,
TSSOP
PLCC
EDIP
1
2
1
PWR
Active Low Power-On Output, Open Drain. The PWR pin is intended for use
as an on/off control for the system power. With VCC voltage removed from
the DS1685/DS1687, PWR can be automatically activated from a kickstart
input by the KS pin or from a wake-up interrupt. Once the system is
powered on, the state of PWR can be controlled by bits in the Maxim
Integrated registers. The PWR pin can be connected through a pullup
resistor to a positive supply. The voltage of the pullup supply should be no
greater than 5.5V.
—
1, 11, 13,
18
2, 3, 16,
20
N.C.
No Connection. Pins missing by design.
2
3
—
X1
Connections for Standard 32.768kHz Quartz Crystal. For greatest
accuracy, the DS1685 must be used with a crystal that has a specified load
capacitance of either 6pF or 12.5pF. The crystal-select (CS) bit in Extended
Control Register 4B is used to select operation with a 6pF or 12.5pF
crystal. The crystal is attached directly to the X1 and X2 pins. There is no
need for external capacitors or resistors. Note: X1 and X2 are very high-
impedance nodes. It is recommended that they and the crystal be guard-
ringed with ground and that high-frequency signals be kept away from the
crystal area.
3
4
—
X2
4–11
5–10, 12,
14
4–11
AD0–AD7
Multiplexed, Bidirectional Address/Data Bus. The addresses are present
during the first portion of the bus cycle and the same pins and signal paths
are used for data in the second portion of the cycle. Address/data
multiplexing does not slow the access time of the DS1685 since the bus
change from address to data occurs during the internal RAM access time.
Addresses must be valid prior to the latter portion of ALE, at which time the
DS1685/DS1687 latches the address. Valid write data must be present and
held stable during the latter portion of the WR pulse. In a read cycle, the
DS1685/DS1687 outputs 8 bits of data during the latter portion of the RD
pulse. The read cycle is terminated and the bus returns to a high-
impedance state as RD transitions high. The address/data bus also serves
as a bidirectional data path for the extended RAM.
12, 16
15, 20
12
GND
Ground
13
16
13
CS
Chip-Select Input, Active-Low. The chip-select signal must be asserted low
during a bus cycle for the RTC portion of the DS1685/DS1687 to be
accessed. CS must be kept in the active state during RD and WR timing.
Bus cycles that take place with ALE asserted but without asserting CS will
latch addresses. However, no data transfer will occur.
14
17
14
ALE
Address-Strobe Input, Active High. A pulse on the address strobe pin
serves to demultiplex the bus. The falling edge of ALE causes the RTC
address to be latched within the DS1685/DS1687.
15
19
15
WR
Write Input, Active Low. The WR signal is an active-low signal. The WR
signal defines the time period during which data is written to the addressed
register.
17
21
17
RD
Read Input, Active Low. RD identifies the time period when the
DS1685/DS1687 drives the bus with RTC read data. The RD signal is an
enable signal for the output buffers of the clock.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BNN-IU-S | CONVERTER MOD DC/DC 18.5V 200W |
| VI-2NZ-MW-F1 | CONVERTER MOD DC/DC 2V 40W |
| MAX5387MAUD+ | IC POT DGTL 256-TAP 14TSSOP |
| CS3106A-32-52S | CONN PLUG 8POS STRAIGHT W/SCKT |
| VE-BNM-IU-S | CONVERTER MOD DC/DC 10V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1685E-3/T&R | 制造商:Maxim Integrated Products 功能描述:IC RTC 3V 64-BIT Y2KC 24-TSSOP |
| DS1685E-3/T&R | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1685E-3/TR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clocks |
| DS1685E-3_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3V/5V Real-Time Clocks |
| DS1685E-3+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。