- 您現在的位置：買賣IC網 > PDF目錄379180 > DS1670 Portable System Controller PDF資料下載
參數資料
| 型號： | DS1670 |
| 英文描述： | Portable System Controller |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 252K |
| 代理商： | DS1670 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
DS1670
10 of 17
The Conversion Update In Progress (CU) bit in the Status Register indicates when the ADC Register can
be read. When this bit is a 1, an update to the ADC Register will occur within 488 ms maximum.
However, when this bit is 0 an update will not occur for at least 244 ms. The CU bit should be polled
before reading the ADC Register to insure that the contents are stable during a read cycle. Once a read
cycle to the ADC Register has been started, the DS1670 will not update that register until the read cycle
has been completed. It should also be mentioned that taking CS low will abort the read cycle and will
allow the ADC Register to be updated.
Figure 6 illustrates the timing of the CU bit relative to an instruction to begin conversion and the
completion of that conversion.
CU BIT TIMING
Figure 6
3-WIRE SERIAL INTERFACE
Communication with the DS1670 is accomplished through a simple 3-wire interface consisting of the
Chip Select (CS), Serial Clock (SCLK) and Input/Output (I/O) pins.
All data transfers are initiated by driving the CS input high. The CS input serves two functions. First, CS
turns on the control logic, which allows access to the shift register for the address/command sequence.
Second, the CS signal provides a method of terminating either single byte or multiple byte (burst) data
transfer. A clock cycle is a sequence of a rising edge followed by a falling edge. For data input, data
must be valid during the rising edge of the clock and data bits are output on the falling edge of the clock.
If the CS input goes low, all data transfer terminates and the I/O pin goes to a high impedance state.
Address and data bytes are always shifted LSB first into the I/O pin. Any transaction requires the
address/command byte to specify a read or write to a specific register followed by one or more bytes of
data. The address byte is always the first byte entered after CS is driven high. The most significant bit
(
RD
/WR) of this byte determines if a read or write will take place. If this bit is 0, one or more read
cycles will occur. If this bit is 1, one or more write cycles will occur.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1670E | Portable System Controller |
| DS1670S | Portable System Controller |
| DS17285 | 3V/5V Real-Time Clock |
| DS17285-3 | 3V/5V Real-Time Clock |
| DS17285-5 | 3V/5V Real-Time Clock |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1670E | 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1670E/T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 20TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRLR SYSTEM PORTABLE 20TSSOP 制造商:Maxim Integrated Products 功能描述:Real Time Clock Portable System Controller |
| DS1670E/T&R | 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1670E/TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Portable System Controller |
| DS1670E+ | 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。