- 您現在的位置：買賣IC網 > PDF目錄358701 > DS1669S TIP POINTED R 0,4MM PDF資料下載
參數資料
| 型號： | DS1669S |
| 英文描述： | TIP POINTED R 0,4MM |
| 中文描述： | 電子數字電位器 |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 151K |
| 代理商： | DS1669S |
DS1669
10 of 10
NOTES:
1.
All inputs; UV, DC, and D are internally pulled up with a resistance of 100k
.
2.
Input logic levels are referenced to -V.
3.
I
CC
is the internal current that flows between -V and +V.
4.
Input leakage applies to contact inputs UC and DC and digital input (D).
5.
Wiper current and rheostat currents are the maximum currents which can flow in the resistive
elements.
6.
Capacitance values apply at 25°C.
7.
Input pulse width is the minimum time required for an input to cause an increment or decrement. If
the UC, DC or D input is held active for longer than 1 second, subsequent increments or decrements
will occur on 100 ms intervals until the inputs UC, DC, and/or D is released to V
IH
.
8.
Repetitive pulsed inputs on UC, DC, or D will be recognized as long as the pulse repetition occurs
within 1 second of each other. Pulses occurring faster than 1 ms apart may not be recognized as
individual inputs but can be interpreted a constant input.
9.
Idle state supply current is measured with no pushbutton depressed and with the wiper. R
W
tied to a
CMOS load.
10.
Maximum time required for the Dallastat to determine single or dual pushbutton operation after input
supply has reached 10% of recommended supply operating conditions.
11.
Absolute linearity is used to determine wiper voltage versus expected voltage as determined by wiper
position.
12.
Relative linearity is used to determine the change in voltage between successive tap positions.
13.
-3 dB cutoff frequency characteristics for the DS1669 depend on potentiometer total resistance:
DS1669-010; 1 MHz, DS1669-050; 200 kHz, DS1669-100; 100 kHz.
14.
Valid at 25
°
C only.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1831S | Multisupply Micromonitor |
| DS1856E-025R | Dual, Temperature-Controlled Resistors with Internally Calibrated Monitors and Password Protection |
| DS1922L | Temperature Logger iButton with 8kB Datalog Memory |
| DS1922T | Temperature Logger iButton with 8kB Datalog Memory |
| DS1922L-F5 | Temperature Logger iButton With 8kB Datalog Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1669S-10 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1669S-10/T&R | 制造商:Maxim Integrated Products 功能描述:IC RHEOSTAT DALLASTAT 10K 8-SOIC |
| DS1669S-10/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1669S-10/T&R/C03 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1669S-10/T&R/C05 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。