- 您現在的位置：買賣IC網 > PDF目錄379180 > DS1626U High-Precision 3-Wire Digital Thermometer and Thermostat PDF資料下載
參數資料
| 型號： | DS1626U |
| 元件分類： | 溫度傳感器 |
| 英文描述： | High-Precision 3-Wire Digital Thermometer and Thermostat |
| 中文描述： | 高精度3線數字溫度計和溫度 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 216K |
| 代理商： | DS1626U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
DS1626/DS1726
8 of 13
CPU BIT AND STAND-ALONE THERMOSTAT OPERATION
In stand-alone thermostat mode, DS1626/DS1726 thermostat functionality can be used without
requiring a microcontroller to start/stop temperature conversions. The CPU bit in the configuration
register determines if stand-alone mode is enabled.
When CPU = 1 stand-alone mode is disabled, and the only way to start/stop temperature conversions is
by using a microcontroller to transmit Start Convert T and Stop Convert T commands, respectively.
Stand-alone mode is enabled when CPU = 0. In this mode, when
RST
= 0 the CLK/
CNV
pin operates
as a control signal to start and stop temperature measurements. Driving CLK/
CNV
low initiates
continuous temperature conversions that will continue until CLK/
CNV
is brought high again. If the
CLK/
CNV
pin is driven low and then returned to a high state in less than 10ms, only one temperature
conversion will be performed after which the DS1626/DS1726 will return to a low-power idle state
(i.e., one-shot operation). Note that when stand-alone mode is enabled, the 1SHOT bit in the
configuration register is ignored, and only the CLK/
CNV
signal determines whether continuous or
one-shot conversions take place.
Since T
H
, T
L
, and the CPU bit are stored in EEPROM, the DS1626/DS1726 can be preprogrammed for
stand-alone operation. If desired, the CLK/
CNV
and
RST
pin can be connected to GND so the
DS1626/DS1726 will automatically begin taking temperature measurements at power-up
Normal bus communication with the DS1626/DS1726 can still take place in stand-alone mode when
RST
= 1. When communication is initiated, stand-alone conversions are automatically halted.
If during
the bus communication continuous temperature conversions are started using the Start Convert T
command, they can only be stopped by issuing a Stop Convert T command.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1726 | High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1726U | High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1642-100 | Nonvolatile Timekeeping RAM |
| DS1642-70 | Nonvolatile Timekeeping RAM |
| DS1642 | Nonvolatile Timekeeping RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1626U/T&R | 制造商:Maxim Integrated Products 功能描述:0.5C 3-WIRE DIG THERM (USOP) T&R - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: |
| DS1626U/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1626U+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1626U+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-USOP 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital Thermometer & Thermostat |
| DS1626U+T&R | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。