- 您現在的位置：買賣IC網 > PDF目錄379179 > DS1621 Digital Thermometer and Thermostat PDF資料下載
參數資料
| 型號： | DS1621 |
| 元件分類： | 溫度傳感器 |
| 英文描述： | Digital Thermometer and Thermostat |
| 中文描述： | 數字溫度計和溫度監控器 |
| 文件頁數： | 5/16頁 |
| 文件大小： | 647K |
| 代理商： | DS1621 |
DS1621
5 of 16
102299
Higher resolutions may be obtained by reading the temperature and truncating the 0.5
°
C bit (the LSB)
from the read value. This value is TEMP_READ. The value left in the counter may then be read by
issuing a READ COUNTER command. This value is the count remaining (COUNT_REMAIN) after the
gate period has ceased. By loading the value of the slope accumulator into the count register (using the
READ SLOPE command), this value may then be read, yielding the number of counts per degree C
(COUNT_PER_C) at that temperature. The actual temperature may be then be calculated by the user
using the following:
TEMPERATURE=TEMP_READ-0.25 +
C
PER
COUNT
REMAIN
COUNT
C
PER
COUNT
(
_
_
)
_
_
_
Thermostat Control
In its operating mode, the DS1621 functions as a thermostat with programmable hysteresis as shown in
Figure 3. The thermostat output updates as soon as a temperature conversion is complete.
When the DS1621’s temperature meets or exceeds the value stored in the high temperature trip register
(TH), the output becomes active and will stay active until the temperature falls below the temperature
stored in the low temperature trigger register (TL). In this way, any amount of hysteresis may be
obtained.
The active state for the output is programmable by the user so that an active state may either be a logic
"1" (V
DD
) or a logic "0" (0V).
THERMOSTAT OUTPUT OPERATION
Figure 3
DQ (Thermostat output, Active=High)
OPERATION AND CONTROL
The DS1621 must have temperature settings resident in the TH and TL registers for thermostatic
operation. A configuration/status register also determines the method of operation that the DS1621 will
use in a particular application, as well as indicating the status of the temperature conversion operation.
The configuration register is defined as follows:
where
DONE = Conversion Done bit. “1” = Conversion complete, “0” = Conversion in progress.
TL
TH
T (°C)
DONE
THF
TLF
NVB
1
0
POL
1SHOT
相關PDF資料 |
PDF描述 |
|---|---|
| DS1624 | Digital Thermometer and Memory |
| DS1626 | High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1626U | High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1726 | High-Precision 3-Wire Digital Thermometer and Thermostat |
| DS1726U | High-Precision 3-Wire Digital Thermometer and Thermostat |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1621+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1621C | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1621C-A7-W | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1621S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1621S/T&R | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER & THERMOSTAT - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。