- 您現在的位置：買賣IC網 > PDF目錄379178 > DS1245YP-85-IND CAT5E PATCH CORD 1 FOOT PINK PDF資料下載
參數資料
| 型號： | DS1245YP-85-IND |
| 英文描述： | CAT5E PATCH CORD 1 FOOT PINK |
| 中文描述： | 1024k非易失SRAM |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 221K |
| 代理商： | DS1245YP-85-IND |
DS1245Y/AB
2 of 12
DESCRIPTION
The DS1245 1024k Nonvolatile SRAMs are1,048,576-bit, fully static, nonvolatile SRAMs organized as
131,072 words by 8 bits. Each complete NV SRAM has a self-contained lithium energy source and
control circuitry which constantly monitors V
CC
for an out-of-tolerance condition. When such a condition
occurs, the lithium energy source is automatically switched on and write protection is unconditionally
enabled to prevent data corruption. DIP-package DS1245 devices can be used in place of existing 128k x
8 static RAMs directly conforming to the popular bytewide 32-pin DIP standard. DS1245 devices in the
PowerCap Module package are directly surface mountable and are normally paired with a DS9034PC
PowerCap to form a complete Nonvolatile SRAM module. There is no limit on the number of write
cycles that can be executed and no additional support circuitry is required for microprocessor interfacing.
READ MODE
The DS1245 executes a read cycle whenever
WE
(Write Enable) is inactive (high) and
CE
(Chip Enable)
and
OE
(Output Enable) are active (low). The unique address specified by the 17 address inputs (A
0
-
A
16
) defines which of the 131,072 bytes of data is to be accessed. Valid data will be available to the eight
data output drivers within t
ACC
(Access Time) after the last address input signal is stable, providing that
CE
and
OE
(Output Enable) access times are also satisfied. If
OE
and
CE
access times are not satisfied,
then data access must be measured from the later occurring signal (
CE
or
OE
) and the limiting parameter
is either t
CO
for
CE
or t
OE
for
OE
rather than address access.
WRITE MODE
The DS1245 executes a write cycle whenever the
WE
and
CE
signals are active (low) after address
inputs are stable. The later occurring falling edge of
CE
or
WE
will determine the start of the write cycle.
The write cycle is terminated by the earlier rising edge of
CE
or
WE
. All address inputs must be kept
valid throughout the write cycle.
WE
must return to the high state for a minimum recovery time (t
WR
)
before another cycle can be initiated. The
OE
control signal should be kept inactive (high) during write
cycles to avoid bus contention. However, if the output drivers are enabled (
CE
and
OE
active) then
WE
will disable the outputs in t
ODW
from its falling edge.
DATA RETENTION MODE
The DS1245AB provides full functional capability for V
CC
greater than 4.75 volts and write protects by
4.5 volts. The DS1245Y provides full functional capability for V
CC
greater than 4.5 volts and write-
protects by 4.25 volts. Data is maintained in the absence of V
CC
without any additional support circuitry.
The nonvolatile static RAMs constantly monitor V
CC
. Should the supply voltage decay, the NV SRAMs
automatically write-protect themselves, all inputs become “don’t care,” and all outputs become high
impedance. As V
CC
falls below approximately 3.0 volts, a power switching circuit connects the lithium
energy source to RAM to retain data. During power-up, when V
CC
rises above approximately 3.0 volts,
the power switching circuit connects external V
CC
to RAM and disconnects the lithium energy source.
Normal RAM operation can resume after V
CC
exceeds 4.75 volts for the DS1245AB and 4.5 volts for the
DS1245Y.
FRESHNESS SEAL
Each DS1245 device is shipped from Dallas Semiconductor with its lithium energy source disconnected,
guaranteeing full energy capacity. When V
CC
is first applied at a level greater than 4.25 volts, the lithium
energy source is enabled for battery back-up operation.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1245Y-85 | 1024k Nonvolatile SRAM |
| DS1245Y-70 | 1024k Nonvolatile SRAM |
| DS1245Y-100 | CABLE SMA/SMA 36 RG-58 |
| DS1245Y-120 | 1024k Nonvolatile SRAM |
| DS1245AB-100 | 1024k Nonvolatile SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS-1246ZJ | 制造商:Hikvision USA 功能描述:Outdoor Wall Mount Gooseneck Bracket 制造商:HIKVISION 功能描述:BRACKET WALL MOUNT OUTDOOR GOOSENECK FOR 71XX CAMERAS |
| DS12470W-150# | 制造商:Maxim Integrated Products 功能描述: |
| DS1248 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:1024k NV SRAM with Phantom Clock |
| DS1248P | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:1024k NV SRAM with Phantom Clock |
| DS1248W-120 | 功能描述:IC NVSRAM 1MBIT 120NS 32DIP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。