- 您現在的位置：買賣IC網 > PDF目錄299010 > DS1231S-20 Power Supply Supervisor PDF資料下載
參數資料
| 型號： | DS1231S-20 |
| 英文描述： | Power Supply Supervisor |
| 中文描述： | 電源監控 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 66K |
| 代理商： | DS1231S-20 |
DS1231/S
022698 5/9
APPLICATION – MODE PIN CONNECTED TO
GROUND
When the Mode pin is connected to ground, pin 1 is a
current source of 30
A with a VTP+ of 2.5 volts. Pin 1 is
held below the trip point by a switching device like an
opto-isolator as shown in Figure 6. Determination of the
sense point has the same criteria as discussed in the
previous application. However, determining component
values is significantly different. In this mode, the maxi-
mum dynamic range of the sense point versus desired
trip voltage is primarily determined by the selection of a
zener diode. As an example, if the maximum voltage at
the sense point is 200V and the desired trip point is
150V, then a zener diode of 150V will approximately set
the trip point. This is particularly true if power consump-
tion on the high voltage side of the opto-isolator is not an
issue. However, if power consumption is a concern,
then it is desirable to make the value of R1 high. As the
value of R1 increases, the effect of the LED current in
the opto-isolator starts to affect the IN trip point. This can
be seen from the equation shown in Figure 6. R1 must
also be low enough to allow the opto-isolator to sink the
30
A of collector current required by pin 1 and still have
enough resistance to keep the maximum current
through the opto-isolator’s LED within data sheet limits.
Figure 7 illustrates how the DS1231 can be interfaced to
the AC power line when the mode pin is grounded.
AC VOLTAGE MONITOR WITH TRANSFORMER ISOLATION Figure 5
+5VDC
IN
MODE
TOL
GND
VCC
NMI
RST
-10% VCC THRESHOLD
TO
P
DS1231
+5VDC
VOLTAGE SENSE POINT
NOTE: RST requires a pull–up resister.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1231S-35 | Power Supply Supervisor |
| DS1231S-50 | Power Supply Supervisor |
| DS1241 | Peripheral IC |
| DS1241N | Peripheral IC |
| DS1241Q | Peripheral IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1231S-20/T&R | 制造商:Maxim Integrated Products 功能描述:POWER MONITOR-20-16PIN-SOIC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POWER MONITOR 20NS 16-SOIC 制造商:Maxim Integrated Products 功能描述:Supervisory Circuits Power Monitor |
| DS1231S-20/T&R | 功能描述:監控電路 Power Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1231S-20+ | 功能描述:監控電路 Power Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| DS1231S-20+T&R | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.62V/4.37V 2000UA 16SOIC W - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POWER MONITOR 20NS 16-SOIC 制造商:Maxim Integrated Products 功能描述:Supervisory Circuits Power Monitor |
| DS1231S-20+T&R | 功能描述:監控電路 Power Monitor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。