參數資料
型號： DS1094L
英文描述： 10/100/1000 Base-T Ethernet LAN Switch
中文描述： 多相擴頻EconOscillator
文件頁數： 8/11頁
文件大小： 590K
代理商： DS1094L
D
will dither between 2MHz and 1.96MHz at a modulation
frequency determined by the selected dither frequen-
cy. Continuing with the same example, if D1 and D0
both equal zero, selecting f
MOSC
/128, then the dither
frequency would be 15.625kHz.
2-Wire Slave Address
The 2-wire serial interface is used to read and write the
control registers of the DS1094L. The default slave
address of the DS1094L is B0h (see Figure 4). Using
the 3 address bits (A2, A1, and A0) in the ADDR regis-
ter, the slave address can be changed to allow as
many as eight DS1094Ls reside on the same 2-wire
bus or to simply prevent address conflicts with other 2-
wire devices. The location of the address bits within the
ADDR register is shown in the
Control Registers
sec-
tion. A detailed description of the 2-wire interface is
found in the
2-Wire Serial Interface Description
section.
EEPROM Write Control
Since EEPROM does have a limited number of lifetime
write cycles (specified in the
NONVOLATILE MEMORY
CHARACTERISTICS
electrical table), it is possible to
configure the DS1094L to prevent EEPROM wear out
and eliminate the EEPROM write cycle time by using
the WC bit in the ADDR register. When the WC bit is 0
(default), register writes are automatically written into
EEPROM. The Write EE Command is not needed.
However, if WC = 1, then register writes are stored in
SRAM and only written to EEPROM when the user
sends the Write EE Command. If power to the device is
cycled, the last value stored in EEPROM is recalled.
The time required to store the values is one EEPROM
write cycle time. WC = 1 is ideal for applications that
frequently modify the frequency/registers.
Regardless of the value of the WC bit, the value of the
ADDR register is always written immediately to EEP-
ROM.
Control Registers
The DS1094L control registers are used to program the
frequency and features of the device. Table 6 lists the
DS1094L’s control registers and illustrates bit locations
as well as other valuable information. The memory
address of each register is shown in the ADDRESS col-
umn. The factory default values programmed into EEP-
ROM are shown in the DEFAULT column. Refer to the
corresponding sections to determine what values to
write to the registers.
PRESCALER (02h)
D1, D0
Ph1, Ph0 Determines whether the two-phase, three-
phase, or four-phase mode is selected. Refer
to Table 3.
J1, J0
Selects the dither amount. Refer to Table 4.
P1, P0
Determines the prescaler value. Refer to
Table 2.
Selects the dither frequency. Refer to Table 5.
DAC (08h)
D3 to D0 This four-bit value determines the master oscil-
lator frequency, f
MOSC
. Refer to Table 1 and
the
Master Oscillator
section for a detailed
information on calculating the DAC value.
ADDR (0Dh)
WC
The EEPROM write control bit determines if
writes to control registers are automatically
backed up in NV memory (EEPROM) or
whether a write EE command is required to
write to NV memory. See the
EEPROM Write
Control
section for more information.
A2 to A0 This three-bit value determines the 2-wire
slave address.
WRITE EE COMMAND (3Fh)
This command can be used when the WC bit = 1 (see
explanation in the
EEPROM Write Control
section) to
transfer registers internally from SRAM to EEPROM. The
time required to store the values is one EEPROM write
cycle time. This command is not needed if WC = 0.
Multiphase Spread-Spectrum EconOscillator
8
_____________________________________________________________________
BINARY
REGISTER
ADDRESS
MSB
LSB
P0
D0
A0
DEFAULT
ACCESS
PRESCALER
DAC
ADDR
WRITE EE Command
02h
08h
0Dh
3Fh
D1
X
1
X
1
D0
X
1
X
1
Ph1
X
1
X
1
Ph0
X
1
X
1
No Data
J1
D3
WC
J0
D2
A2
P1
D1
A1
11001101b
XXXX0000b
XXXX0000b
R/
W
R/
W
R/
W
W
Table 6. Control Registers
X = Don’t care
X
1
= Don’t care, reads as 1
相關PDF資料
PDF描述
DS1094LU Multiphase Spread-Spectrum EconOscillator
DS1099 Low-Frequency Dual EconOscillator
DS1099U Space-Saving, 8-Channel Relay/Load Driver
DS1104SG25 Rectifier Diode
DS1104SG26 Rectifier Diode
相關代理商/技術參數
參數描述
DS1094LU-350+ 制造商:Maxim Integrated Products 功能描述:
DS1094LU-42M 功能描述:可編程振蕩器 Multiphase Spread Spctrm EconOscillatr RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1094LU-42M+ 功能描述:可編程振蕩器 Multiphase Spread Spctrm EconOscillatr RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1094LU-42M+T 功能描述:可編程振蕩器 Multiphase Spread Spctrm EconOscillatr RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
DS1099U-01M 功能描述:可編程振蕩器 Low-Frequency Dual EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*