- 您現在的位置：買賣IC網 > PDF目錄9142 > DS1087LU-26A+ (Maxim Integrated Products)IC ECONOSILL 3.3V SS 8-USOP PDF資料下載
參數資料
| 型號： | DS1087LU-26A+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ECONOSILL 3.3V SS 8-USOP |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 系列： | EconOscillator™ |
| 類型： | 時鐘發生器 |
| PLL： | 無 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:1 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 66MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 2.7 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
| 產品目錄頁面： | 1436 (CN2011-ZH PDF) |
DS1087L
3.3V Spread-Spectrum EconOscillator
_____________________________________________________________________
9
Bits 3 to 0:
Prescaler Divider. The prescaler bits
(bits P3 to P0) divide the master oscillator
frequency by 2x where x can be from 0 to
8. Any prescaler bit value entered that is
greater than 8 decodes as 8.
ADDR Register
Bit 3:
Write Control. The WC bit determines if
the EEPROM is to be written to after reg-
ister contents have been changed. If WC
= 0 (default), EEPROM is written automat-
ically after a write. If WC = 1, the EEP-
ROM is only written when the WRITE EE
command is issued. See the WRITE EE
Command section for more information.
Bits 2 to 0:
Address. The A0, A1, A2 bits determine
the lower nibble of the 2-wire slave
address.
WRITE EE Command
The WRITE EE command is useful in closed-loop appli-
cations where the registers are frequently written. In
applications where the register contents are frequently
written, the WC bit should be set to 1 to prevent wear-
ing out the EEPROM. Regardless of the value of the WC
bit, the value of the ADDR register is always written
immediately to EEPROM. When the WRITE EE com-
mand has been received, the contents of the registers
are copied into the EEPROM, thus locking in the regis-
ter settings.
_______2-Wire Serial Port Operation
2-Wire Serial Data Bus
The DS1087L communicates through a 2-wire serial
interface. A device that sends data onto the bus is
defined as a transmitter, and a device receiving data
as a receiver. The device that controls the message is
called a "master." The devices that are controlled by the
master are "slaves." A master device that generates the
serial clock (SCL), controls the bus access, and gener-
ates the START and STOP conditions must control the
bus. The DS1087L operates as a slave on the 2-wire
bus. Connections to the bus are made through the
open-drain I/O lines SDA and SCL.
The following bus protocol has been defined (see
Figures 3 and 5):
Data transfer can be initiated only when the bus is
not busy.
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH are
interpreted as control signals.
Accordingly, the following bus conditions have been
defined:
Bus not busy: Both data and clock lines remain
HIGH.
Start data transfer: A change in the state of the
data line, from HIGH to LOW, while the clock is
HIGH, defines a START condition.
Stop data transfer: A change in the state of the
data line, from LOW to HIGH, while the clock line
is HIGH, defines the STOP condition.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
12
8
9
3–7
Figure 3. 2-Wire Data Transfer Protocol
相關PDF資料 |
PDF描述 |
|---|---|
| X9C503S | IC DIGITAL POT 50K 100TP 8SOIC |
| VI-23D-MW-S | CONVERTER MOD DC/DC 85V 100W |
| GTC06F-20-15S | CONN PLUG 7POS STRAIGHT W/SCKT |
| X9C503PI | IC DIGITAL POT 50K 100TP 8DIP |
| MS27473E24B1PA | CONN PLUG 128POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1087LU-26A/T | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1087LU-26A/T+W | 功能描述:可編程振蕩器 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1087LU-26A/W | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1087LU-26A+ | 功能描述:可編程振蕩器 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1087LU-26A+T | 功能描述:可編程振蕩器 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
發布緊急采購，3分鐘左右您將得到回復。