- 您現在的位置：買賣IC網 > PDF目錄9240 > DS1040Z-100+ (Maxim Integrated Products)IC DELAY LINE 5TAP 100NS 8-SOIC PDF資料下載
參數資料
| 型號： | DS1040Z-100+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/6頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DELAY LINE 5TAP 100NS 8-SOIC |
| 標準包裝： | 100 |
| 標片/步級數： | 5 |
| 功能： | 單發射，可編程 |
| 延遲到第一抽頭： | 20ns |
| 接頭增量： | 20ns |
| 可用的總延遲： | 100ns |
| 獨立延遲數： | 1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
DS1040
6 of 6
tRISE (Input Rise Time): The elapsed time between the 20% and the 80% point on the leading edge of
the input pulse.
tFALL (Input Fall Time): The elapsed time between the 80% and the 20% point on the trailing edge of
the input pulse.
tD (Intrinsic Delay): The elapsed time between the 1.5 point on the leading edge of the input trigger
pulse and the 1.5V point on the leading edge of output pulse.
tPU (Power-up Time): After VCC is valid, the time required before timing specifications is within
tolerance.
TEST SETUP DESCRIPTION
Figure 4 illustrates the hardware configuration used for measuring the timing parameters on the DS1040.
The input waveform is produced by a precision pulse generator under software control. The intrinsic
delay is measured by a time interval counter (20 ps resolution) connected between the input and each
output. Outputs are selected and connected to the counter by a VHF switch control unit. Width
measurements are made by directing both the start and stop functions of the counter to the same output.
All measurements are fully automated, with each instrument controlled by a central computer over an
IEEE 488 bus.
TEST CONDITIONS
Input:
Ambient Temperature:
25
°C + 3°C
Supply Voltage (VCC):
5.0V + 0.1V
Input Pulse:
High = 3.0V + 0.1V
Low = 0.0V + 0.1
Source Impedance:
50 ohm max.
Rise and Fall Time:
3.0 ns max. (measured
between 0.6V and 2.4)
Pulse Width:
500 ns (1
ms for -500)
Period:
1
ms (2 ms for -500)
Output:
The output is loaded with a 74F04. Delay is measured at the 1.5V level on the rising and falling edge.
Note:
Above conditions are for test only and do not restrict the operation of the device under other data sheet
conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1013M-50+ | IC DELAY LINE 50NS 8-DIP |
| X9314WSZ-3 | IC XDCP SGL 32-TAP 10K 8-SOIC |
| DS1013M-40+ | IC DELAY LINE 40NS 8-DIP |
| MS27508E24F35PB | CONN RCPT 128POS BOX MNT W/PINS |
| DS1013M-75+ | IC DELAY LINE 75NS 8-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1040Z-100+ | 功能描述:延遲線/計時元素 RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1040Z-150 | 功能描述:延遲線/計時元素 RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1040Z-150+ | 功能描述:延遲線/計時元素 RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
| DS1040Z-200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Pulse Generator |
| DS1040Z-200+ | 功能描述:延遲線/計時元素 RoHS:否 制造商:Micrel 功能:Active Programmable Delay Line 傳播延遲時間:1000 ps 工作溫度范圍: 封裝 / 箱體:QFN-24 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。