參數資料
型號: DRV102
英文描述: PWM SOLENOID/VALVE DRIVER
中文描述: 脈寬調制電磁/閥驅動
文件頁數: 14/19頁
文件大?。?/td> 253K
代理商: DRV102
14
DRV102
The difficulty in selecting the heat sink required lies in
determining the power dissipated by the DRV102. For dc
output into a purely resistive load, power dissipation is simply
the load current times the voltage developed across the
conducting output transistor times the duty cycle. Other loads
are not as simple. Once power dissipation for an application
is known, the proper heat sink can be selected.
Heat Sink Selection Example
A TO-220 package’s maximum dissipation is 2 Watts. The
maximum expected ambient temperature is 80
°
C. Find the
proper heat sink to keep the junction temperature below
125
°
C.
Combining Equations 1 and 2 gives:
T
J
= T
A
+ P
D
(
θ
JC
+
θ
CH
+
θ
HA
)
(3)
T
J
, T
A
, and P
D
are given.
θ
JC
is provided in the Specifica-
tions table, 3
°
C/W.
θ
CH
can be obtained from the heat sink
manufacturer. Its value depends on heat sink size, area, and
material used. Semiconductor package type, mounting screw
torque, insulating material used (if any), and thermal
joint compound used (if any) also affect
θ
CH
. A typical
θ
CH
for a TO-220 mounted package is 1
°
C/W. Now we can solve
for
θ
HA
:
(4)
To maintain junction temperature below 125
°
C, the heat
sink selected must have a
θ
HA
less than 18.5
°
C/W. In other
words, the heat sink temperature rise above ambient must be
less than 37
°
C (18.5
°
C/W 2W). For example, at 2 Watts
Thermalloy model number 6030B has a heat sink
temperature rise of about 33
°
C above ambient, which is
below the 37
°
C required in this example. Figure 13 shows
power dissipation versus ambient temperature for a TO-220
package with a 6030B heat sink.
Another variable to consider is natural convection versus
forced convection air flow. Forced-air cooling by a small fan
can lower
θ
CA
(
θ
CH
+
θ
HA
) dramatically. Heat sink manufac-
turers provide thermal data for both of these cases. For
additional information on determining heat sink require-
ments, consult Application Bulletin AB-038.
As mentioned earlier, once a heat sink has been selected, the
complete design should be tested under worst-case load and
signal conditions to ensure proper thermal protection.
θ
θ
(
θ
θ
HA
J
A
D
JC
CH
HA
T
T
P
=
+
)
=
+ °
)
=
125 C – 80 C
2W
– 3 C/W
18.5 C/W
相關PDF資料
PDF描述
DRV102F PWM SOLENOID/VALVE DRIVER
DRV102T PWM SOLENOID/VALVE DRIVER
DRV1100 HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER
DRV1100P HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER
DRV1100U HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER
相關代理商/技術參數
參數描述
DRV102F 制造商:BB 制造商全稱:BB 功能描述:PWM SOLENOID/VALVE DRIVER
DRV102F/500 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/ Valve Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV102FKTWT 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/ Valve Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV102FKTWTG3 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/Valve Drvr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
DRV102T 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/ Valve Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube