- 您現在的位置：買賣IC網 > PDF目錄379175 > DRV101 PWM SOLENOID/VALVE DRIVER PDF資料下載
參數資料
| 型號： | DRV101 |
| 英文描述： | PWM SOLENOID/VALVE DRIVER |
| 中文描述： | 脈寬調制電磁/閥驅動 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 298K |
| 代理商： | DRV101 |
11
DRV101
An under-current fault occurs when the output current is
below the under-scale current threshold (typically 23mA).
For example, this function indicates when the load is discon-
nected. Again, the flag output is not latched, so an under-
current condition during PWM mode will produce a flag
output that is modulated by the PWM waveform. An initial,
brief under-current flag normally appears driving inductive
loads and may be avoided by adding a parallel resistor
sufficient to move the initial current above the under-current
threshold. An under-current flag may not appear for case
temperatures above 100
°
C. Avoid adding capacitance to pin
6 (Out) as it may cause momentary current limiting.
Over-Temperature Fault
A thermal fault occurs when the die reaches approximately
165
°
C, producing a similar effect as pulling the input low.
Internal shutdown circuitry disables the output and resets the
Delay Adjust pin. The Flag is latched in the low state (fault
condition) until the die has cooled to approximately 150
°
C.
A thermal fault can occur in any mode of operation. Recov-
ery from thermal fault will start in delay mode (constant dc
output).
PACKAGE MOUNTING
Figure 9 provides recommended PCB layouts for both the
TO-220 and DDPAK power packages. The tab of both
packages is electrically connected to ground (pin 4). It may
be desirable to isolate the tab of TO-220 package from its
mounting surface with a mica (or other film) insulator (see
FIGURE 9. TO-220 and DDPAK Solder Footprints.
7-Lead DDPAK
(1)
(Package Drawing #328)
7-Lead TO-220
(Package Drawing #327)
NOTE: (1) For improved thermal performance increase footprint area.
See Figure 11, “Thermal Resistance vs Circuit Board Copper Area”.
Mean dimensions in inches. Refer to end of data sheet
or Appendix C of Burr-Brown Data Book for tolerances
and detailed package drawings.
0
0
0.05
0
0.51
0.105
0.05
0.035
0.04
0
0
Over/Under Current Fault
An over-current fault occurs when the output current is
greater than approximately 2.3A. The status flag is not
latched. Since current during PWM mode is switched on and
off, the flag output will be modulated with PWM timing (see
flag waveforms in the Typical Performance Curves).
FIGURE 8. LED to Indicate Fault Condition.
DRV101
Thermal Shutdown
Over/Under Current
4
6
7
Out
5k
+5V
Flag
(LED)
HLMP-Q156
相關PDF資料 |
PDF描述 |
|---|---|
| DRV101F | PWM SOLENOID/VALVE DRIVER |
| DRV101T | PWM SOLENOID/VALVE DRIVER |
| DRV102 | PWM SOLENOID/VALVE DRIVER |
| DRV102F | PWM SOLENOID/VALVE DRIVER |
| DRV102T | PWM SOLENOID/VALVE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DRV101F | 制造商:BB 制造商全稱:BB 功能描述:PWM SOLENOID/VALVE DRIVER |
| DRV101F/500 | 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/ Valve Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| DRV101FKTWT | 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/ Valve Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| DRV101FKTWT | 制造商:Texas Instruments 功能描述:DRIVERS 制造商:Texas Instruments 功能描述:IC, SOLENOID/VALVE DRVR 1CH 2.3A D2PAK-7 |
| DRV101FKTWTG3 | 功能描述:馬達/運動/點火控制器和驅動器 PWN SOLENOID/VALVE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。