- 您現在的位置：買賣IC網 > PDF目錄171217 > DPGM-C8-33S-B-2 (ITT CANNON) 8 CONTACT(S), FEMALE, MULTIWAY RACK AND PANEL CONN, CRIMP, PLUG PDF資料下載
參數資料
| 型號： | DPGM-C8-33S-B-2 |
| 廠商： | ITT CANNON |
| 元件分類： | 多腳機架和面板連接器 |
| 英文描述： | 8 CONTACT(S), FEMALE, MULTIWAY RACK AND PANEL CONN, CRIMP, PLUG |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 338K |
| 代理商： | DPGM-C8-33S-B-2 |
Coaxial Contact Assembly (DPGM/DPJM)
Cable Stripping
AB
C
50 Ohm Contact (RG-196U)
(assembly steps 1,
2, 3, 4, 5 & 8)
75 Ohm Contact (RG-187U)
(assembly steps 1,
2, 3, 5 & 8)
95 Ohm Contact (RG-195U)
(assembly steps 1,
3, 6, 7 & 8)
BUSHING
SHIM
CRIMP RING
JACKET
DIELECTRIC
1 . After the coaxial cable has been stripped to the
proper dimensions, tin the center conductor. If
O.D. of cable is less than .096 (2.44), slip
rubber bushing over wire. (50, 75 & 95 ohm)
2. Assemble crimp ring under braid and add bush-
ing to cable. (50 & 75 ohm)
3. The center contact is supplied loose in the
polyethylene bag. Insert the tinned conductor
into the contact. Wire must be visible through
inspection hole and dielectric pushed against
contact shoulder. For 150 ohm contact shoulder
must be flush against bushing. Heat contact
with a clean soldering iron. Avoid solder outside
contact, (50, 75, & 95 ohm)
4. Wrap shim around braid. (50 ohm)
7. Slip crimp over the braid. (95 ohm)
8. Crimp - crimp tool must be located 1/16
(1.58) to 5 / 64 (1.98) from shoulder of coaxial.
(50, 75 & 95 ohms)
5. Feed cable and assembled parts into coaxial
shell. Care is required if braid is to fit smoothly
inside the shell. (50 & 75 ohm)
6. Thread crimp ring over cable. Feed center con-
tact into coaxial shell with the shell between the
dielectric and the braid. (95 ohm)
CRIMP RING
BRAID
BUSHING
CENTER CONDUCTOR
INSPECTION HOLE
CENTER CONDUCTOR
CENTER CONTACT
DIELECTRICAPPLY CLEAN SOLDERING IRON
SHIM
CENTER CONTACT
SEALING GROMMET LOACATION
.125 (3.18) MIN. PLUG
.063 (1.59) MIN. RECPT
.063 (1.59)
.078 (1.98)
EDGE OF
CRIMP TOOL
JACKET
BRAID
CRIMP RING
SHELL
CRIMP RING
.035 DIA
(0.89)
D E F
Cable Trim Dimensions
A
150 ohm
95 ohm
75 ohm
50 ohm
3/16 (4.76)
1/4 (6.35)
1/16 (1.59)
1/8 (3.18)
5/32 (3.97)
5/64 (1.98)
.154 (3.91)
.106 (2.69)
.122 (3.10)
.106 (2.69)
.183 (4.65)
.139 (3.53)
.158 (4.01)
.136 (3.53)
.202 (5.13)
.153 (3.89)
B
CD
min. dia.
E
max. dia.
F
min. dia.
Cable Entry Dimensions
DPGM/DPJM/DPJMB
Assembly Procedures
103
www.ittcannon.com
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
Assembly Steps
相關PDF資料 |
PDF描述 |
|---|---|
| DPGM-C8-33S-K-2 | 8 CONTACT(S), FEMALE, MULTIWAY RACK AND PANEL CONN, CRIMP, PLUG |
| DPGM-C8-34P-B-2 | 8 CONTACT(S), MALE, MULTIWAY RACK AND PANEL CONN, CRIMP, RECEPTACLE |
| DPGM-C8-34P-K-2 | 8 CONTACT(S), MALE, MULTIWAY RACK AND PANEL CONN, CRIMP, RECEPTACLE |
| DPGM-C8-34S-B-2 | 8 CONTACT(S), FEMALE, MULTIWAY RACK AND PANEL CONN, CRIMP, RECEPTACLE |
| DPGM-C8-34S-K-2 | 8 CONTACT(S), FEMALE, MULTIWAY RACK AND PANEL CONN, CRIMP, RECEPTACLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DPGM-C8-33S-K | 制造商:ITT Interconnect Solutions 功能描述:DPGM-C8-33S-K - Bulk |
| DPGM-C8-34P-A | 制造商:ITT Interconnect Solutions 功能描述:DPGM-C8-34P-A - Bulk |
| DPGM-C8-34P-B | 制造商:ITT Interconnect Solutions 功能描述:DPGM-C8-34P-B - Bulk |
| DPGW-04 | 制造商:DWYER INSTRUMENTS 功能描述:Pressure Gauge, Digital, 0 to 5 psi Range, +/-1% Accuracy, for Liquids/Gases |
| DPGW-05 | 制造商:DWYER INSTRUMENTS 功能描述:Pressure Gauge, Digital, 0 to 15 psi Range, +/-1% Accuracy, for Liquids/Gases |
發布緊急采購，3分鐘左右您將得到回復。