- 您現在的位置：買賣IC網 > PDF目錄376801 > DM8108 (Electronic Theatre Controls, Inc.) 8 port 10/100M Fast Ethernet Switching Controller PDF資料下載
參數資料
| 型號： | DM8108 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 8 port 10/100M Fast Ethernet Switching Controller |
| 中文描述： | 8端口10/100M快速以太網交換控制器 |
| 文件頁數： | 20/35頁 |
| 文件大?。?/td> | 371K |
| 代理商： | DM8108 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
DM8108
8 port 10/100M Fast Ethernet Switching Controller
20
Preliminary
Version: DM8108-DS-P02
November 25, 1999
Auto-Negotiation
Auto-negotiation disabled
When ANEG* (MA[7:0]) strap pin is high, auto-
negotiation is disabled, and the corresponding port
can be selected as half- or full- duplex mode
respectively. Following the RESET the port duplex
mode is set by the state sampled on the TXEN(7:0)
pins. The speed that each port operates in (10Mbps
or 100Mbps) is determined by the frequency of
TxCLK(7:0) and RxCLK(7:0) generated by PHY. The
PHY generates 25MHz clock for both TxCLK and
RxCLK in 100Mbps operation and 2.5MHz clock in
10Mbps operation.
Auto-negotiation enabled
When ANEG* (MA[7:0]) pins are tied low, the MAC
decodes the duplex mode from the values of the
Auto-Negotiation Advertisement Register and the
Auto-Negotiation Link Partner Ability Register at the
end of Auto-negotiation process. Once the duplex
mode is resolved, the DM8108 updates the port
control registers. The DM8108 will continuously
perform the following operations for each port (PHY
address 0-7 alternatively), implemented as READ
commands issued via the MDCLK/MDIO interface:
Link Detection and Link Detection Bypass
(FLNK*)
The DM8108 will continuously query the PHY devices
for their link status associated with Auto-Negotiation
Process. The DM8108 will alternatively read
registers from PHY address 0 to 7 and update the
internal link bits according to the value of bit 2 of
register 1. In case of link down (bit 1.2=0), that port
will enter “l(fā)ink test fail state”. In this state, all the port’s
logic go to a reset state. The port will enter the “l(fā)ink
up state” if the bit 1.2 is “1” or the FLNK* (force link,
LEDSTB* strobed low during reset) pin is sampled low
during reset.
Partition Mode
A port enters partition mode when more than 64
consecutive collisions are seen on the port. In partition
mode the port continuous to transmit but it will not receive.
A port returned to normal operation mode when a good
packet is seen on the wire.
Enabling Partition Mode
Partitioned mode is enabled always.
Entering Partition State
A port will enter the Partition state when PAEN* strap pin
sampled low during reset and when either of the following
conditions occurs:
The port detects a collision on every one of 64
consecutive re-transmit attempts to the same packet.
The port detects a single collision which occurs for
more than 512 bit times.
While in Partition state:
The port will continue to transmit its pending packet,
regardless of the collision detection, and will not allow
the usual Back-off Algorithm. Additional packets
pending for transmission, will be transmitted, while
ignoring the internal collision indication. This frees up
the port’s transmit buffers which would otherwise be
filled up at the expense of other ports buffers. The
assumption is that the partition is signifying a system
failure situation (bad connection/cable/station), thus
dropping packets is a small price to pay vs. the cost of
halting the switch due to a buffer full condition. The
partition indication is available via the LED interface.
Exiting from Partition State
The Port exits from Partition State, following the end of a
successful packet transmission. A successful packet
transmission is defined as no collisions were detected on the
first 512 bits of the transmission.
Expansion Bus
The expansion bus operates at Full-Duplex mode that
provides up-to 7200Mbps bandwidth for device to
device connection. Several DM8108 can be
cascaded as a pipe to provide a robust Ethernet
Switching system.
The bus itself is very simple. The transmit and receive ports
contain independent data, valid and handshake signals.
No bus arbitration is involved.
相關PDF資料 |
PDF描述 |
|---|---|
| DM8121W | 8-Input Digital Multiplexer |
| DM8123N | 2-Input Digital Multiplexer |
| DM7123J | 2-Input Digital Multiplexer |
| DM7123W | 2-Input Digital Multiplexer |
| DM8123W | 2-Input Digital Multiplexer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM-810A | 功能描述:數字萬用表 DMM,TRMS 1000V AC/DC 600mA to 10A RoHS:否 制造商:Tektronix 產品:Multimeters 類型:Bench 準確性:0.04 % 電壓范圍:2 V to 2 kV 電阻范圍: 電容范圍: 顯示計數: 頻率:10 Hz to 45 Hz, 850 Hz to 1 MHz 測距: 真均方根值: 數據保持: |
| DM-810A-C | 功能描述:數字萬用表 DMM,TRMS 1000V AC/DC 600mA to 10A, CALIB RoHS:否 制造商:Tektronix 產品:Multimeters 類型:Bench 準確性:0.04 % 電壓范圍:2 V to 2 kV 電阻范圍: 電容范圍: 顯示計數: 頻率:10 Hz to 45 Hz, 850 Hz to 1 MHz 測距: 真均方根值: 數據保持: |
| DM8121J/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Input Digital Multiplexer |
| DM8121N/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Input Digital Multiplexer |
| DM8121N/B+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Input Digital Multiplexer |
發布緊急采購，3分鐘左右您將得到回復。