- 您現在的位置：買賣IC網 > PDF目錄258062 > DM1601-9RV0A 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | DM1601-9RV0A |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE M02, MODULE |
| 文件頁數： | 24/25頁 |
| 文件大?。?/td> | 569K |
| 代理商： | DM1601-9RV0A |
Cassette Style
DC-DC Converters
M Series
Edition 01/01.2001
8/25
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
Output Protection
Each output is protected against overvoltages which could
occur due to a failure of the internal control circuit. Voltage
suppressor diodes (which under worst case condition may
become a short circuit) provide the required protection. The
suppressor diodes are not designed to withstand externally
applied overvoltages. Overload at any of the outputs will
cause a shut-down of all outputs. A red LED indicates the
overload condition of the respective output.
Parallel and Series Connection
Main outputs of equal nominal voltage can be connected in
parallel. It is important to assure that the main output of a
multiple output module is forced to supply a minimum cur-
rent of 0.1 A to enable correct operation of its own auxiliary
outputs.
In parallel operation, one or more of the main outputs may
operate continuously in current limitation which will cause
an increase in case temperature. Consequently, a reduction
of the max. ambient temperature by 10 K is recommended.
Main or auxiliary outputs can be connected in series with
any other output of the same or another module. In series
connection, the maximum output current is limited by the
lowest current limit. Output ripple and regulation values are
added. Connection wiring should be kept as short as possi-
ble.
If output terminals are connected together in order to estab-
lish multi-voltage configurations, e.g. +5.1 V,
±12 V etc. the
common ground connecting point should be as close as
possible to the connector of the converter to avoid exces-
sive output ripple voltages.
Auxiliary outputs should never be connected in parallel!
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the:
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 50% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05031
TA min
TC max
Convection cooling
Fig. 6
Output current derating versus temperature for -7 and -9
units.
1.0
0
0.5
U
o1
0.5
U
o1 nom
I
o
I
o nom
1.0
1.2
I
o nom
I
o1
I
o2,Io3
I
oL1
I
oL2,IoL3
.95
05022
Io/Io nom
1
uod
t d
DUo I
t
Uo
0
t
≥10 s
05010
Fig. 4
Typical output voltage Uo1 versus output currents Io.
Fig. 5
Dynamic load regulation uo d versus load change.
相關PDF資料 |
PDF描述 |
|---|---|
| DM1901-7RD1F | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| DM1901-7RV2H | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| DM1901-9PD3 | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| DM1901-9PD5F | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| DM1901-9PD6HF | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM160211 | 功能描述:觸摸傳感器開發工具 mTouch Projected Cap Dev Kit RoHS:否 制造商:Cypress Semiconductor 工具用于評估: 接口類型: 工作電壓: 最大工作溫度: |
| DM160213 | 功能描述:開發板和工具包 - PIC / DSPIC BodyCom System Development Kit RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
| DM160214 | 制造商:Microchip Technology Inc 功能描述:LIGHTING COMMUNICATIONS DEVELOPMENT PLATFORM - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:BOARD DEV LIGHTING COMM MAIN 制造商:Microchip Technology Inc 功能描述:PIC16F1947 LIGHTING COMMUNICA 制造商:Microchip Technology Inc 功能描述:PIC16F1947 LIGHTING COMMUNICATION BOARD 制造商:Microchip Technology Inc 功能描述:PIC16F1947, LIGHTING COMMUNICATION BOARD 制造商:Microchip Technology Inc 功能描述:PIC16F1947, LIGHTING COMMUNICATION BOARD, Silicon Manufacturer:Microchip, Core A 制造商:Microchip Technology Inc 功能描述:Lighting Communications Development Platform, General Purpose 制造商:Microchip Technology Inc 功能描述:PIC16F1947, LIGHTING COMMUNICATION BOARD, Silicon Manufacturer:Microchip, Core Architecture:PIC, Core Sub-Architecture:PIC16F, Silicon Core Number:PIC16F1947, Silicon Family Name:PIC16F19xx, Kit Contents:Communication Board |
| DM160217 | 功能描述:位置傳感器開發工具 MGC3130-Sabrewing Evaluation Kit RoHS:否 制造商:Microchip Technology 工具用于評估: 接口類型: 工作電壓: |
| DM160218 | 制造商:Microchip Technology Inc 功能描述:MGC3130 SINGLE ZONE DEVELOPMENT KIT "HILLSTAR" - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:KIT MGC3130 SINGLE ZONE HILLSTAR 制造商:Microchip Technology Inc 功能描述:MGC3130 Single Zone Development Kit "Hillstar" 制造商:Microchip Technology Inc 功能描述:MGC3130 Single Zone Development Kit "Hillstar", Accessories |
發布緊急采購，3分鐘左右您將得到回復。