- 您現在的位置：買賣IC網 > PDF目錄1912 > DLP-245PB-G (DLP Design Inc)MODULE USB-MCU FT245RL W/16F877A PDF資料下載
參數資料
| 型號： | DLP-245PB-G |
| 廠商： | DLP Design Inc |
| 文件頁數： | 12/16頁 |
| 文件大小： | 0K |
| 描述： | MODULE USB-MCU FT245RL W/16F877A |
| 產品目錄繪圖： | DLP-245PB-G |
| 標準包裝： | 1 |
| 系列： | USB |
| 模塊/板類型： | 開發板 |
| 適用于相關產品： | USB |
| 產品目錄頁面： | 635 (CN2011-ZH PDF) |
| 其它名稱： | 813-1004 |
V2.3
Page 5 of
15
February 2007
QUICK START GUIDE
This guide requires the use of a Windows 98/2000/XP PC that is equipped with a USB port.
1. Download the DLL (D2XX) version of the device drivers from either dlpdesign.com or
ftdichip.com. Unzip the drivers onto a blank floppy disk or into a folder on the hard drive.
2. The DLP-245PB-G can be configured to receive its operating power from the USB port or
from user electronics. Pins 18, 19, and 20 allow for this configuration. (Refer to the Pinout
Description in the next section for a detailed description of the DLP-245PB-G electrical
interface.)
Note: The board will not operate until a power source has been selected as mentioned in
Step 2.
3. Connect the DLP-245PB-G board to the PC via a standard A-B, 6-foot USB cable. This
action initiates the loading of the USB drivers. When prompted, select the folder where the
DLL version of the device drivers was stored in Step 1. Windows will then complete the
installation of the device drivers for the DLP-245PB-G board. The next time the DLP-245PB-
G board is attached, the host PC will immediately load the correct drivers without any
prompting. Reboot the PC if prompted to do so.
The DLP-245PB-G is shipped with default VID, PID, etc. values programmed into the EEPROM
memory. You only need to run MPROG if you want to change the default values.
At this point, the DLP-245PB-G is ready for use. Note that the DLP-245PB-G will appear
non-responsive if data sent from the host PC is not read from the FT245RL device by the
16F877A microcontroller.
If changing drivers from the VCP to the DLL type (or vice versa), you must first uninstall the
currently loaded drivers. To accomplish this, first disconnect the DLP-245PB-G adapter from the
host computer and then use Add-Remove-Programs in Control Panel.
相關PDF資料 |
PDF描述 |
|---|---|
| DLP-245PL-G | MOD USB-MCU FT245RL W/18LF8722 |
| DLP-245SY-G | MODULE USB-MCU FT245RL W/SX48 |
| DLP-FPGA | MODULE USB-TO-FPGA TRAINING TOOL |
| DLP-HS-FPGA3 | MODULE USB-TO-FPGA SPARTAN 3A |
| DP83848CVVX/NOPB | TXRX ETHERNET PHYTER 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DLP-245PB-G-CCS | 功能描述:界面模塊 DLP-245PB-G BOARD + CCS Compiler RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-245PL | 功能描述:界面模塊 USB/Micro Dev Board ***Last Time Buy*** RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-245PL-G | 功能描述:界面開發工具 USB/Micro Dev Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| DLP-245PL-G-CCS | 功能描述:界面開發工具 DLP-245PL PACKAGED w/CCS Compiler RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| DLP-245SX | 功能描述:界面模塊 USB/Micro Dev Board RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。