<dl id="hyc7a"><menuitem id="hyc7a"><optgroup id="hyc7a"></optgroup></menuitem></dl>
<kbd id="hyc7a"><th id="hyc7a"></th></kbd>
<ins id="hyc7a"><menu id="hyc7a"></menu></ins>
  • 參數資料
    型號: DJIXE972MPAA4
    廠商: Intel Corp.
    英文描述: Single-Port 10/100 Mbps PHY Transceiver
    中文描述: 單端口10/100 Mbps的物理層收發器
    文件頁數: 51/92頁
    文件大?。?/td> 666K
    代理商: DJIXE972MPAA4
    Intel
    LXT972M Single-Port 10/100 Mbps PHY Transceiver
    Datasheet
    Document Number: 302875-005
    Revision Date: 27-Oct-2005
    51
    5.8.4
    10BASE-T Link Integrity Test
    In 10BASE-T mode, the LXT972M Transceiver always transmits link pulses.
    If the Link Integrity Test function is enabled (the normal configuration), the LXT972M
    Transceiver monitors the connection for link pulses. Once link pulses are detected, data
    transmission is enabled and remains enabled as long as either the link pulses or data
    transmission continue. If the link pulses stop, the data transmission is disabled.
    If the Link Integrity Test function is disabled (which can be done by setting Configuration
    Register bit 16.14 to ‘1’), the LXT972M Transceiver transmits to the connection regardless of
    detected link pulses.
    5.8.5
    Link Failure
    Link failure occurs if the Link Integrity Test is enabled and link pulses or packets stop being
    received. If this condition occurs, the LXT972M Transceiver returns to the auto-negotiation phase
    if auto-negotiation is enabled. If the Link Integrity Test function is disabled by setting
    Configuration Register bit 16.14 to ‘1’, the LXT972M Transceiver transmits packets, regardless of
    link status.
    5.8.6
    10BASE-T SQE (Heartbeat)
    By default, the Signal Quality Error (SQE) or heartbeat function is disabled on the LXT972M
    Transceiver. To enable this function, set Register bit 16.9 = 1. When this function is enabled, the
    LXT972M Transceiver asserts its COL output for 5 to 15 bit times (BT) after each packet.
    5.8.7
    10BASE-T Jabber
    If a transmission exceeds the jabber timer, the LXT972M Transceiver disables the transmit and
    loopback functions. For jabber timing parameters, see
    Figure 26, “Intel LXT972M Transceiver
    10BASE-T Jabber and Unjabber Timing” on page 69
    .
    The LXT972M Transceiver automatically exits jabber mode after the unjabber time has expired.
    This function can be disabled by setting Register bit 16.10 = 1.
    5.8.8
    10BASE-T Polarity Correction
    The LXT972M Transceiver automatically detects and corrects for the condition in which the
    receive signal (TPIP/N) is inverted. Reversed polarity is detected if eight inverted link pulses - or
    four inverted end-of-frame (EOF) markers - are received consecutively. If link pulses or data are
    not received by the maximum receive time-out period (96 to 128 ms), the polarity state is reset to a
    non-inverted state. When polarity reversal is detected in 10BASE-T operation, register 17.5 is set
    to 1. (For details, see bit 17.5 in
    Table 52, “Status Register #2 - Address 17, Hex 11” on page 85
    .)
    相關PDF資料
    PDF描述
    DJIXE972MPCA4 Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MPEA4 Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MQAA4 Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MQCA4 Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MQEA4 Single-Port 10/100 Mbps PHY Transceiver
    相關代理商/技術參數
    參數描述
    DJIXE972MPCA4 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MPEA4 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MQAA4 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MQCA4 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Single-Port 10/100 Mbps PHY Transceiver
    DJIXE972MQEA4 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Single-Port 10/100 Mbps PHY Transceiver