參數資料
型號： DIW5029
元件分類： 電源模塊
英文描述： DC-DC REG PWR SUPPLY MODULE
封裝： DIP-8/23
文件頁數： 4/8頁
文件大?。?/td> 273K
代理商： DIW5029
4
Test Configurations
Input Reflected-Ripple Current Test Setup
+Out
-Out
+Vin
-Vin
DC / DC
Converter
Load
Battery
+
Lin
+
Cin
To Oscilloscope
Current
Probe
Input reflected-ripple current is measured with a inductor
Lin (4.7uH) and Cin (220uF, ESR < 1.0 at 100 KHz) to
simulate source impedance. Capacitor Cin is to offset
possible battery impedance. Current ripple is measured at
the input terminals of the module and measurement
bandwidth is 0-500 KHz.
Peak-to-Peak Output Noise Measurement
Scope measurement should be made by using a BNC
socket, measurement bandwidth is 0-20 MHz. Position the
load between 50 mm and 75 mm from the DC/DC
Converter. A Cout of 0.47uF ceramic capacitor is placed
between the terminals shown below.
+Out
-Out
+Vin
-Vin
Single Output
DC / DC
Converter
Resistive
Load
Scope
Copper Strip
Cout
+Out
-Out
+Vin
-Vin
Dual Output
DC / DC
Converter
Resistive
Load
Scope
Copper Strip
Cout
Com.
Scope
Cout
Design & Feature Considerations
The DIW5000 circuit block diagrams are shown in
Figures 5 and 6.
PFM
Isolation
Ref.Amp
LC
Filter
+Vin
-Vin
-Vo
+Vo
Figure 5: Block diagram of DIW5000 single output
modules.
+Vo
PFM
Isolation
Ref.Amp
LC
Filter
+Vin
-Vin
Com.
-Vo
Figure 6: Block diagram of DIW5000 dual output
modules
Input Source Impedance
The power module should be connected to a low ac-
impedance input source. Highly inductive source
impedances can affect the stability of the power module.
+
+Out
-Out
+Vin
-Vin
DC / DC
Converter
Load
DC Power
Source
+
-
Cin
In applications where power is supplied over long lines
and output loading is high, it may be necessary to use a
capacitor at the input to ensure startup.
Capacitor mounted close to the input of the power
module helps ensure stability of the unit, it is
recommended to use a good quality low Equivalent
Series Resistance (ESR < 1.0 at 100 KHz) capacitor of
a 12uF for the 12V input devices, a 4.7uF for the 24V
input devices, and a 2.2uF for the 48V devices.
相關PDF資料
PDF描述
DJ1GARAO SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 2A, 12VDC, THROUGH HOLE-RIGHT ANGLE
DK-621-0411-P CABLE TERMINATED, MALE, TRIAXIAL CONNECTOR, SOLDER, PLUG
DK-621-0411-S CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, SOLDER, PLUG
DK-621-0412-P CABLE TERMINATED, MALE, TRIAXIAL CONNECTOR, SOLDER, JACK
DK-621-0412-S CABLE TERMINATED, FEMALE, TRIAXIAL CONNECTOR, SOLDER, JACK
相關代理商/技術參數
參數描述
DIW6 7321000 制造商:Belden Inc 功能描述:CAT3 6PR U/UTP CMR REEL
DIX4192 制造商:BB 制造商全稱:BB 功能描述:Integrated Digital Audio Interface Receiver and Transmitter
DIX4192EVM-PDK 功能描述:音頻 IC 開發工具 DIG AUDIO INTERFACE RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
DIX4192IPFB 功能描述:音頻發送器、接收器、收發器 Dig Aud Interface Xceiver RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
DIX4192IPFBG4 功能描述:音頻發送器、接收器、收發器 Dig Aud Interface Xceiver RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*