![](http://datasheet.mmic.net.cn/Intersil/DG508ACJZ_datasheet_96883/DG508ACJZ_4.png)
4
FN3137.6
March 4, 2009
Source OFF Leakage
Current, IS(OFF)
VS = +10V, VD = -10V
-1
0.002
1
-5
0.002
5
nA
VS = -10V, VD = +10V
-1
-0.005
1
-5
-0.005
5
nA
Drain OFF Leakage
Current, ID(OFF)
VEN = 0V
VS = -10V, VD = +10V
-
0.01
10
-
0.01
20
nA
VS = +10V, VD = -10V
-10
-0.015
-
-20
-0.015
-
nA
Drain ON Leakage Current,
ID(ON)
(Note 6)
Sequence Each
Switch ON
VAL = 0.8V,
VAH = 2.4V
VD = VS(ALL) = +10V
-
0.015
10
-
0.015
20
nA
VD = VS(ALL) = -10V
-10
-0.03
-
-20
-0.03
-
nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
VEN = 5.0V (Enabled) or
VEN = 0V (Standby), VA = 0V
-
1.3
2.4
-
1.3
2.4
mA
Negative Supply Current, I-
-1.5
-0.7
-
-1.5
-0.7
-
mA
Electrical Specifications
TA = 25
oC, V+ = +15V, V- = -15V, GND = 0V, V
EN = 2.4V, Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
“A” SUFFIX
“B” AND “C” SUFFIX
UNITS
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
Electrical Specifications
TA = Over Operating Temperature Range, V+ = +15V, V- = -15V, GND = 0V, VEN = 2.4V,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
“A” SUFFIX
UNITS
MIN
(NOTE 3)
TYP
MAX
DIGITAL INPUT CHARACTERISTICS
Address Input Current, Input Voltage
High, IAH
VA = 2.4V
-30
-
μA
VA = 15V
-
30
μA
Address Input Current Input Voltage
Low, IAL
VEN = 2.4V
VA = 0V
-30
-
μA
VEN = 0V
-30
-
μA
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
(Note 7)
-15
-
+15
V
Drain-Source ON Resistance, rDS(ON)
Sequence Each Switch ON
VAL = 0.8V, VAH = 2.4V
IS = -200μA, VD = +10V
-
500
Ω
IS = -200μA, VD = -10V
-
500
Ω
Source OFF Leakage Current, IS(OFF)
VEN = 0V
VS = +10V, VD = -10V
-
50
nA
VS = -10V, VD = +10V
-50
-
nA
Drain OFF Leakage Current, ID(OFF)
VEN = 0V
VS = -10V, VD = +10V
-
200
nA
VS = +10V, VD = -10V
-200
-
nA
Drain ON Leakage Current, ID(ON)
(Note 6) Sequence Each Switch ON
VAL = 0.8V, VAH = 2.4V
VD = VS(ALL) = +10V
-
200
nA
VD = VS(ALL) = -10V
-200
-
nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
VEN = 5.0V, VA = 0V
-3.2
-
4.5
mA
Negative Supply Current, I-
-3.2
-
4.5
mA
Positive Standby Supply Current, I+
VEN = 0V, VA = 0V
-3.2
-
4.5
mA
Negative Standby Supply Current, I-
-3.2
-
4.5
mA
NOTES:
3. Typical values are for design aid only, not guaranteed and not subject to production testing.
4. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet.
5. Off isolation = 20Log |VS|/|VD|, where VS = input to Off switch, and VD = output due to VS.
6. ID(ON) is leakage from driver into “ON” switch.
7. Parameter not tested. Parameter guaranteed by design or characterization.
DG508A